Mecha: Chogokin and the Making of Gunpla

Toys Almanac · Giant Robots

Mecha: Chogokin and the Making of Gunpla

The tin robot of the 1950s was wound by a key. The giant robot of the 1970s was a television hero cast in metal, and the robot of the 1980s arrived in pieces on a plastic tree, to be assembled at a kitchen table. This chapter follows that change, from Mazinger Z to Gunpla.

Fact sheet

First chogokinGA-01 Mazinger Z, Popy, 1972
First Jumbo MachinderMazinger Z, 1973
Gunpla launchJuly 1980, Bandai
Snap-fit kits1987 and 1988
ShipmentsOver 800 million Gunpla by September 2024
Last reviewed28 October 2026

At a glance

  1. A metal from a manga. Chogokin means super alloy, the fictional metal of Go Nagai's Mazinger Z, and Popy used the word for a die-cast robot line from 1972.
  2. Big, light and hollow. The Jumbo Machinder of 1973 was a roto-moulded plastic robot about 24 inches tall, and the first one sold roughly 400,000 units in five months.
  3. Made again for the West. Mattel sold chogokin and Jumbo Machinder toys abroad in the late 1970s as Shogun Warriors, many of them heavily altered.
  4. A toy that arrives in pieces. Bandai's Gundam kits of 1980 replaced the finished toy with a model that the buyer assembled, and the same idea still sells today.
  5. Rarely discontinued. Wikipedia says Gunpla kits are almost never officially discontinued, apart from minor problems such as mould damage.
Frame

Three Ways to Hold a Robot

Japanese robot toys can be sorted by how the child met them. In the first period, covered in the chapter on tin robots, the robot was a mechanical curiosity, wound with a key or driven by batteries, and printed in bright lithography. In the second, it was a television character that the child had already seen on a screen. In the third, it was a set of parts that the child, or more often a teenager, built.

Mecha toys in nine dates, as the sources give them1971Popy formedwithin Bandai1972Mazinger Zairs; chogokinname adopted1973First JumboMachinder1979Gundam ontelevision1980Bandai Gundamkits1987Snap-fit kits1990High Grade andthe gradesystem1995Master Grade2010Real Grade;30thanniversaryWikipedia (Bandai, Chogokin, Jumbo Machinder, Mazinger Z, Gunpla). Spacing is even, not to scale. Diagram by Japonista.
Nine dates in robot toy history
Diagram by Japonista. Dates from Wikipedia; spacing is even, not to scale.
Look closer: The dates are crowded between 1971 and 1980. Almost everything that a collector now sorts into categories was invented in those ten years.
Diagram by Japonista

The change happened in about a decade. The Wikipedia article on Mazinger Z gives the broadcast start as 3 December 1972, the article on chogokin gives the same year for the first die-cast figure, the article on Jumbo Machinder gives 1973 for the first large plastic robot, and the article on Gunpla gives 1980 for the first Bandai Gundam kit. Between the first and last of these dates, the toy moved from a metal object to a plastic one, and from something played with to something made.

This chapter is built on those articles and on the sources named at the end. Where they disagree, it says so. Where they are silent, as they are about the individual price of a toy or the exact production count of a figure, it makes no claim. No open-licence photograph of a 1970s chogokin or Jumbo Machinder was found for this chapter, so the photographs show the kit, the shop and the character in public life. The house does not hold Gunpla or chogokin at the time of writing, and the shelf near the end of the chapter says so plainly.

Origin

A Traffic Jam and a Cockpit

Mazinger Z is a manga by Go Nagai that became an anime, and the Wikipedia article on it records how the idea arose. Nagai had loved Astro Boy and Tetsujin 28 as a child and wanted to make his own robot, but for a long time he could not find a concept that did not borrow too heavily from them. The solution came from a traffic jam: drivers at the back would welcome a way to bypass the cars ahead, and that thought led to a giant robot controlled from the inside, like a car.

The first design, named Energer Z, was driven by a motorcycle that was ridden up its back and into its head. Because Kamen Rider had made motorcycles popular, the article says, Nagai replaced the motorcycle with a hovercraft so that the robot would stand out. He then renamed it Mazinger Z, a play on the Japanese words for demon and god. The manga began in Weekly Shonen Jump in October 1972, and the television series ran on Fuji TV from 3 December 1972 to 1 September 1974, for 92 episodes.

The article describes the programme as one that introduced many stock features of the super robot genre, including the first mecha piloted from within a cockpit, and records its ratings: episode 68, broadcast on 17 March 1974, reached 30.4 per cent, the highest of the series. It also reports that Mazinger Z had reached a total of 20 million copies in circulation worldwide as of July 2023. For a toy historian, the lesson is the order of events. The character was a hit on television before the toy existed, and the toy was designed to look like something the child already loved.

The same article notes the name of the metal. In the story the robot is built from Super-Alloy Z, which the Japanese calls Chogokin Zetto. That word, adopted by a toy company, became the name of a whole class of objects, and it is the thread that links the manga to the metal figures described in the next section.

A caution on the sourcesThe Wikipedia article on Mazinger Z does not discuss Popy, Jumbo Machinder or Shogun Warriors, and it gives no separate sales figures for toys. The toy facts in this chapter come from the articles on chogokin, Jumbo Machinder and Bandai.
Metal

Popy and the Super Alloy

Bandai was founded on 5 July 1950 by Naoharu Yamashina as Bandai-ya, and the Wikipedia article on the company says that its breakthrough came in 1963 with action figures based on Astro Boy. After that success, it began funding television series and sponsoring them, using advertising to promote its tie-in figures. In 1971 it formed a subsidiary named Popy, which made toys of popular children's characters and was at first aimed at candy shops and other retailers outside the toy trade.

The article on chogokin says that Popy adopted the name in 1972 for a line of die-cast metal robot and character toys, and that its first release was the GA-01 Mazinger Z. The article records that the engineering was questionable enough for Popy to run a free replacement campaign, and that the toy nevertheless started a craze that changed the Japanese toy industry in the 1970s. A toy that needed to be replaced and still sold in large numbers is a fair measure of how much the television character mattered.

Chogokin figures were made in two main classes. The ST, or standard, figure was usually about five inches tall, which is roughly 12 or 13 centimetres. The DX, or deluxe, figure was much larger and typically had separating parts and more complex weapons, often projectiles that could be launched. Fists were a common projectile, the article says, as a tribute to Mazinger Z as the first chogokin. The detail explains why so many surviving robots are missing a fist, and why a dealer who describes one should say whether the launched parts are present.

After the 1980s, the article records, die-cast metal declined sharply in mass-market robot toys, and PVC and ABS plastic became the main materials. Bandai still continues the line under its own name. The word has also become a general name for Japanese die-cast robot toys among collectors, although it is a registered trademark of Bandai. For that reason other companies use the ending gokin instead, as in Takatoku Toys' Z-Gokin and Max Factory's Max Gokin.

Class Size named in the source Typical features
ST (standard) About 5 inches, roughly 12 to 13 cm Smaller figure, fewer parts
DX (deluxe) Much larger, no figure given Separating parts, complex weapons, often launched fists
Scale

The Robot You Could Almost Ride

The Jumbo Machinder is Popy's large plastic robot of the 1970s. The Wikipedia article on it explains that the name is a trademark but that collectors often use it for any large robot toy roto-moulded from PET, the same plastic used for shampoo bottles. The first, released in 1973, depicted Mazinger Z. It was originally planned at about one metre tall but was scaled down for safety reasons, and it sold roughly 400,000 units in its first five months in the shops. After Popy's success, the article says, other firms including Takatoku, Nakajima and Clover also made large plastic robots.

Most Jumbo Machinders stand about 24 inches tall, although not all do. The article lists the Popy releases by year: Mazinger Z, Kamen Rider V3, Ultraman Taro and Super Robot Red Baron in 1973; Kamen Rider X, Great Mazinger, Super Robot Mach Baron, Ultraman Leo and three Getter Robo figures in 1974; UFO Robo Grendizer, Spazer, Getter Dragon, Getter Liger, Getter Poseidon, Brave Raideen and Ganbare Robocon in 1975; and so on to a Godzilla in 1978 and Dragon Dol in 1982. Several of these characters were not robots at all, which shows that the large hollow toy was a format, not a genre.

Popy changed the line over time. In 1976 and 1977 some figures were sold as Jumbo Machinder Deluxe, which looked largely the same. For the 1979 and 1980 season, Popy redesigned and rebranded the series as Kyodai Robotto Kojo, which means Giant Robot Factory. Those toys came disassembled, and children assembled them with a simple tool included in the box, an early sign of the approach that Gunpla would later make famous. They also had more complex features, such as spring-loaded shooting fists. From 1981 the series was renamed Super Jumbo Machinder.

A separate line, the Kikaiju, took the enemy characters from Mazinger Z and Kamen Rider V3. These were made of soft vinyl instead of PET, stood about 20 inches tall, and, in the article's words, looked very different from the Jumbo Machinders. Ten were released in three waves, with gimmicks that grew from a simple pinball-style launcher to shooting discs, spears and heads. The article names five of them: Doublas M-2, Garada K-7, King Dan X-10, Gelbros J-3 and Spartan K-5. They are a reminder that the soft vinyl monster and the plastic robot were made by the same hands in the same years.

  • First Jumbo Machinder: Mazinger Z, 1973, about 400,000 sold in five months.
  • Usual height: about 24 inches; the Kikaiju stand about 20 inches.
  • Material: roto-moulded PET; the Kikaiju are soft vinyl.
  • Giant Robot Factory, 1979 to 1980: supplied in pieces, with spring-loaded fists.
  • Revivals: a modern Jumbo Machinder in 2009; Toynami's 24-inch Shogun Warriors from 2010; a Mazinger Z reissue announced by Bandai in 2024.
Export

Shogun Warriors and the American Shelf

In the late 1970s, according to the Jumbo Machinder article, several of Popy's robots were retooled for sale in the United States and Europe as Shogun Warriors. Mattel acquired the rights to release them in North America and Europe. One figure, Dragun, was nearly identical to its Japanese version, but Mattel heavily modified most of the others, and Gaiking and Daimos were redesigned entirely. The line included Great Mazinger, sold as Mazinga, Getter Dragon, sold as Dragun, Raideen, sold as Raydeen, and, in the United States, a Godzilla and a Rodan made for that market.

The names changed from country to country. The article says UFO Robo Grendizer was released only in Europe and Canada, and was sold as Goldorak in France and Quebec and as Goldrake in Italy. It also lists four Astro Robot figures released only in Italy, mostly built from parts of Raideen, Gaiking and Grendizer. For a collector, the practical point is that the name on the box tells the market and not always the maker's original design, a rule that the chapter on makers and brands states for tin toys as well.

Safety rules shaped the toys. The article on chogokin records that after a boy died from choking on a missile fired from a Mattel Battlestar Galactica toy, many later Shogun Warriors toys had their spring-loaded missiles modified to fire child-safe projectiles that met the safety rules. That is the reason a well-worn Shogun Warrior of the late 1970s may carry a different weapon from its Japanese twin, and why a description should state which version is in front of the buyer.

Bandai America tried a second route. The same article says that its Godaikin line of the early 1980s was aimed at an older audience and was largely identical to the Japanese originals, and that the high price for the average consumer contributed to the line's end. The two American attempts, one heavily adapted and one faithful, show the same problem from opposite sides: a toy made for a Japanese child did not travel simply.

After

Super Alloy for Grown-Ups

Chogokin did not end with the 1970s. The Wikipedia article describes Bandai's Soul of Chogokin, whose first release was an updated Mazinger Z, as a line of updated versions of toys first made by Popy in the 1970s and 1980s, expanded since to include modern robots that had no earlier chogokin toy. It also gives older shows, such as Dancouga and the Leopardon of the Japanese Spider-Man television series, more accessible figures.

Two further lines show how the audience changed. Souchaku Henshin, which the article says debuted in 2000, makes figures at a five-inch scale of tokusatsu characters from Kamen Rider, the Metal Hero series and Garo, with removable armour and die-cast parts. Super Robot Chogokin, introduced in 2010 as a more affordable alternative to Soul of Chogokin, made figures about 140 millimetres tall with fewer die-cast parts but more articulation, and was retired as of 2016. Today's chogokin products, the article concludes, are usually expensive, high-quality items aimed at collectors.

The large plastic robot was revived as well. The Jumbo Machinder article records a new line for adult collectors in 2009, at about 22 inches and made of ABS and vinyl instead of polyethylene, with only one character produced so far. In 2010 Toynami revived the Shogun Warriors name with 24-inch figures, the first two being GoLion and Dairugger XV, which were adapted in the West as Voltron. In 2024 Bandai announced a reissue of the original Mazinger Z toy, with its built-in spring-loaded firing fists.

For a buyer, these revivals create the same question that the Myths chapter addresses for tin: is this the original or a later production? The answer begins with the material. A 1970s Jumbo Machinder is roto-moulded PET, and a 2009 revival is ABS and vinyl. The dates, materials and boxes in the sources are enough to separate them, and a good description states which one is meant.

Kits

A Toy That Arrives in Pieces

The Gundam story begins with a licence. The Wikipedia article on Gunpla says that Mobile Suit Gundam debuted as a television show in 1979, and that the earlier licensee, Clover, made toys in the style of most children's toys, fully assembled and ready to play. In 1980 Bandai obtained the rights to make Gundam models. It chose a different product, a plastic kit that the buyer assembled, similar to a military vehicle model, and the article says this appealed to the teenagers and adults who were the show's typical audience and was well received.

The Bandai article gives the month: in July 1980 Bandai launched the Gundam plastic model, creating the Gunpla range of scale model kits. Wikipedia's article on Gunpla records the early results: Bandai sold over 100 million units between 1980 and 1984. Nearly every mecha in the series became a kit, including mobile suits, support aircraft and space battleships. Parts came in up to three colours cast into the plastic, but the early kits lacked articulation, had low detail and needed glue.

The name itself is a compression. Gunpla is short for Gundam plamo, and plamo blends the words plastic and model. The article credits the series' creator, Yoshiyuki Tomino, as the inventor of the franchise and says that Bandai made the kits from 1980 to 2017 and that Bandai Spirits has made them since 2017. The Bandai article gives 15 February 2018 as the date on which Bandai Spirits was established and 1 April 2018 as the date on which the adult-focused division moved into it. The sources therefore differ by a year on the change of maker, and this chapter prints both.

Scale matters to the buyer more than the toy's age. A kit is a replica sized by the dimensions given in the fiction, so a 1:60 scale means each inch of the model equals 60 inches of the machine. The article lists the heights of the standard RX-78-2 Gundam at 12.5 cm in 1:144, 18 cm in 1:100, 30 cm in 1:60 and 37.5 cm in the 1:48 Mega Size Model, so the number printed on a box is also a size guide before the box is opened.

Where the sources differWho has made Gunpla since 2017? The Wikipedia article on Gunpla says Bandai Spirits has made the kits since 2017. The Wikipedia article on Bandai says Bandai Spirits was established on 15 February 2018 and took over the adult-focused figures and plastic models division on 1 April 2018. This chapter prints both and prefers neither.
Craft

Sprue, Gate and Snap

A kit is made on a tree. The Gunpla article explains that parts come on a sprue, a grid of runners that carried the molten plastic into the mould cavities, and that each part is attached to the runner through a small gate. The builder cuts the parts free, usually cleans up the gate remnants with clippers, a blade or sandpaper, and then snaps the parts together. Decals are included. The Commons photographs on this page show a modern Real Grade kit of a Zaku II taken apart in this way.

A clear plastic bag of grey and green plastic runners and a decal sheet lying in an open card box on a wooden table.
A kit as it comes
A Real Grade MS-06F Zaku II kit in its original shipping box with all the plastic parts. Photographed by Gravis; CC BY-SA 4.0. Photograph by Gravis, CC BY-SA 4.0. Wikimedia Commons, File:Gunpla model packed.jpg.
Look closer: This is the 'toy that arrives in pieces': a box, a bag, a decal sheet and a tree of parts.
Image: Gravis, CC BY-SA 4.0, via Wikimedia Commons
Green and dark grey plastic runners laid out on a wooden table, each carrying many small parts, with clear parts at the edge.
The runners laid out
Parts of a Real Grade Zaku II kit, still on their sprues. Photographed by Gravis; CC BY-SA 4.0. Photograph by Gravis, CC BY-SA 4.0. Wikimedia Commons, File:Gunpla model sprues.jpg.
Look closer: Each part hangs on a runner by a small gate, as the Wikipedia article describes.
Image: Gravis, CC BY-SA 4.0, via Wikimedia Commons

The first improvements were mechanical. In 1985, the article says, Bandai began using poly-caps, soft polyethylene connectors, to improve the articulation of joints. In 1987 the Gundam Sentinel line introduced snap-fit models that needed little or no glue, and in 1988 snap-fit assembly became standard, so all kits after that required no glue. A technique called System Injection allowed one part to be moulded in several colours at once, which reduced the need for painting.

A dark blue body panel part still attached to a green and blue runner on a wooden surface, in close-up.
A panel on its runner
A single body panel of a Real Grade Zaku II kit, still attached to its sprue. Photographed by Gravis; CC BY-SA 4.0. Photograph by Gravis, CC BY-SA 4.0. Wikimedia Commons, File:Gunpla body panel sprues.jpg.
Look closer: The small round mark at the corner is where the gate was. A careful builder removes it with clippers and sands what is left.
Image: Gravis, CC BY-SA 4.0, via Wikimedia Commons
A runner in which a single moulded part shows blue and green plastic together, resting on a wooden table.
Two colours in one part
Part of a Real Grade Zaku II kit showing how one part is moulded in several colours. Photographed by Gravis; CC BY-SA 4.0. Photograph by Gravis, CC BY-SA 4.0. Wikimedia Commons, File:Gunpla multi color sprue.jpg.
Look closer: This is the effect of System Injection, which reduces the need for painting.
Image: Gravis, CC BY-SA 4.0, via Wikimedia Commons
A dark blue part joined to a green runner by a small nub, on a wooden table.
The nub on a part
A part from a Real Grade Zaku II kit that has been clipped from the runner. Photographed by Gravis; CC BY-SA 4.0. Photograph by Gravis, CC BY-SA 4.0. Wikimedia Commons, File:Gunpla sprue nub.jpg.
Look closer: Clipping leaves a nub, and the nub is how a finished model can be told from a careless one.
Image: Gravis, CC BY-SA 4.0, via Wikimedia Commons

Materials are named plainly. Plastic kits use thermoplastics such as ABS, polypropylene or polystyrene, and Bandai makes them in Japan or China and holds an exclusive worldwide licence for manufacturing and marketing them. Garage kits, also called resin kits, use thermoset polyurethane resin and must be glued together, and the article says Bandai released some of them under its B-Club label, unpainted and without decals. A few kits are metal, usually at about Master Grade size, and can take days to build.

The structure of a modern kit can include an internal frame, a fully articulated skeleton that can stand alone, with panels attached over it. The article adds that some kits had this frame pre-assembled on the runner but that this approach has mostly been phased out because the softer plastic degrades over time. That single remark is useful to a collector of old kits: a sealed box is not a guarantee that its plastic has stayed as it was made, and the Collector's Guide returns to the question of how plastics age.

A pair of blue-handled side-cutters lying on a wooden table beside a green runner of plastic parts.
The builder's tool
Side-cutters sold by a Japanese model shop for use with Gunpla and other kits. Photographed by Gravis; CC BY-SA 4.0. Photograph by Gravis, CC BY-SA 4.0. Wikimedia Commons, File:Gunpla sprue cutter.jpg.
Look closer: Kits start under twenty US dollars and need no special tools, according to Wikipedia; clippers are the usual exception.
Image: Gravis, CC BY-SA 4.0, via Wikimedia Commons
Black and green foot parts of a model robot, partly assembled, lying beside a pair of side-cutters on a pale surface.
A foot under construction
A foot unit from a Real Grade Zaku II kit, assembled but not yet mounted. Photographed by Gravis; CC BY-SA 4.0. Photograph by Gravis, CC BY-SA 4.0. Wikimedia Commons, File:Gunpla foot assembly.jpg.
Look closer: Snap-fit means no glue: the pieces press together.
Image: Gravis, CC BY-SA 4.0, via Wikimedia Commons
Line Year Scale named What the source says
No Grade 1980 Various The first kits, before the grade names; limited articulation, some needed glue and paint.
High Grade (HG) 1990 1:144 Fully snap-fit, with System Injection colour moulding.
Master Grade (MG) Summer 1995 1:100 More parts, better detail and improved articulation.
Perfect Grade (PG) 1998 1:60 Body-on-frame design, with light-up features; the highest and costliest grade.
Real Grade (RG) 2010 1:144 An inner skeletal frame and near-perfect colour without stickers.
Super Deformed (SD) BB Senshi from 1987 None Large heads and simple builds; the line ran to 2018.
Entry Grade (EG) 2011; rebooted 2020 Similar to HG Few parts and limited articulation; the 2020 reboot went worldwide.
Mega Size Model 2010 1:48 About three times the size of an HG kit; thin gates that break by hand.
Ladder

From Entry to Perfect

Bandai introduced the grade system in 1990, with the High Grade line, to describe each kit's detail and quality. The article explains that the High Grade kits had much higher detail and articulation than their 1:144 scale suggested, with features such as the Core Block System, in which the pilot sits in a removable core, and the transformation of the Zeta Gundam. In 1993 a unified set of poly-cap joints was created for smaller-scale kits so that many models could share one skeletal frame, which let Bandai release more models in less time.

Dark grey runners holding the joint and frame parts of a model robot, laid on a wooden table.
The inner frame
Internal frame parts of a Real Grade Zaku II kit. Photographed by Gravis; CC BY-SA 4.0. Photograph by Gravis, CC BY-SA 4.0. Wikimedia Commons, File:Gunpla internal frame sprues.jpg.
Look closer: The Real Grade of 2010 added an inner skeletal frame to the 1:144 size, according to Wikipedia.
Image: Gravis, CC BY-SA 4.0, via Wikimedia Commons
A pale sheet of decals printed with round dots, panel marks and small lettering, with a Bandai logo at the corner, on a wooden table.
A decal sheet
One decal sheet from a Real Grade Zaku II kit. Photographed by Gravis; CC BY-SA 4.0. Photograph by Gravis, CC BY-SA 4.0. Wikimedia Commons, File:Gunpla decal sheet.jpg.
Look closer: Decals are included with the kit, as the article says; the Real Grade is noted for extensive decals.
Image: Gravis, CC BY-SA 4.0, via Wikimedia Commons

The Master Grade followed in summer 1995 at 1:100, with more parts, better detail and improved articulation. The Perfect Grade, at 1:60, debuted in 1998 with the RX-78-2 and is described as Bandai's highest grade, with extensive detail, articulation, light-up features and a body-on-frame design in which exterior panels attach to a working internal frame. The article says only 19 kits at that scale have been released since, and that the Perfect Grade is usually the most expensive line.

Budget lines recur. The First Grade of 1999 offered simple 1:144 snap-fit kits for the franchise's twentieth anniversary. Non-graded kits at 1:144 appeared for Gundam SEED, with only the critical joints, and the Entry Grade of 2011, sold in parts of Asia, was discontinued and rebooted worldwide in 2020, with the RX-78-2 as its first kit. The Real Grade of 2010, made for the thirtieth anniversary, added an inner skeletal frame and near-perfect colour without stickers to the 1:144 size.

The Super Deformed kits stand outside the scale system. The article says they have large heads, simple builds, and a need for paint, and that the best-known line, BB Senshi, ran from 1987 to 2018. As of March 2021, according to the article, Bandai Namco reported 714.84 million total units: 538.24 million standard Gundam units since 1980 and 176.6 million Super Deformed units since 1987. By September 2024, cumulative worldwide shipments had passed 800 million. A line that large is not a niche, and the dates on a box are an essential part of a description.

Hobby

Panel Lines, Dioramas and a Giant on the Waterfront

The kit made a hobby. The article says Gundam model building is a worldwide pastime, and that some people build kits as sold while others add paint and decals, combine parts from several kits or create detailed multi-layer paint jobs. Kits start at under 20 US dollars and need no special tools, so the barrier to entry is low. Hobbyists also create dioramas using techniques from model railways and wargaming, showing combat, maintenance or battlefield wreckage, and customise kits by panel lining, scribing, weathering and kitbashing.

The hobby has its own media. The article lists four titles that focus on Gunpla: Plamo-Kyoshiro in 1982, Model Suit Gunpla Builders Beginning G in 2010, Gundam Build Fighters in 2013 and Build Fighters Try in 2014, followed by Build Divers in 2018. It adds that Bandai runs the annual Gunpla Builders World Cup in at least sixteen countries, with winners receiving trophies and kits.

A long curved wall of lit glass shelves filled with small model robots and figures in a white shop interior.
A wall of finished kits
Display cases of kits at Odaiba, Tokyo, August 2014; photographed by Piotrus; CC BY-SA 3.0. Photograph by User:Piotrus, CC BY-SA 3.0. Wikimedia Commons, File:Odaiba Tokyo August 2014 Gundam 014.JPG.
Look closer: Finished models in a case show what the sprues become.
Image: User:Piotrus, CC BY-SA 3.0, via Wikimedia Commons
A glass display case with a red rope barrier showing a boxed kit labelled MG Ver. 3.0 and the words RX-78-2 Gundam in large letters.
Master Grade, version 3.0
A display of the Master Grade RX-78-2 Version 3.0 at Odaiba, Tokyo, August 2014; photographed by Piotrus; CC BY-SA 3.0. Photograph by User:Piotrus, CC BY-SA 3.0. Wikimedia Commons, File:Odaiba Tokyo August 2014 Gundam 017.JPG.
Look closer: Wikipedia dates the Master Grade RX-78-2 Version 3.0 to 2014, the franchise's thirty-fifth anniversary.
Image: User:Piotrus, CC BY-SA 3.0, via Wikimedia Commons

The best-known object of the culture is a statue. As part of the thirtieth anniversary, the article says, Bandai announced the Real-G project on 11 March 2009, and the 1:1 scale, 18-metre RX-78-2 statue was completed on 9 June 2009 and shown in a Tokyo park. It moved to Shizuoka City from July 2010 to March 2011, was dismantled in August 2011, and reopened in Odaiba, Tokyo, on 19 April 2012. In 2017 it was replaced by a Unicorn Gundam in front of Gundam Front Tokyo. The same statue was the model for the 2010 Real Grade and Mega Size Model kits.

A white life-sized Unicorn Gundam statue stands with its arm out in front of a glass tower under a grey sky.
The Unicorn Gundam
The life-sized Unicorn Gundam in Japan; CC0, photographed by Pelpinosas R. Justin James. Photograph by Pelpinosas R. Justin James, CC0. Wikimedia Commons, File:Life-Sized Unicorn Gundam Statue.jpg.
Look closer: Wikipedia says the Unicorn replaced the 18-metre RX-78-2 in front of Gundam Front Tokyo in 2017.
Image: Pelpinosas R. Justin James, CC0, via Wikimedia Commons
The shoulder and chest of a huge Gundam statue seen from below, with a blue and white shoulder plate marked WB and a crane arm at the edge.
A shoulder of the statue
The Gundam statue at Odaiba, Tokyo; photographed by Sun Taro; CC BY-SA 2.0. Photograph by Sun Taro, CC BY-SA 2.0. Wikimedia Commons, File:GUNDAM@ODAIBA - Flickr - sun summer.jpg.
Look closer: At 18 metres, the statue is the same design as the 1:144 kit, enlarged to the dimensions the fiction gives.
Image: Sun Taro, CC BY-SA 2.0, via Wikimedia Commons

A kit shop in the West shows how far the hobby has travelled. The Commons photograph of a Gunpla pop-up store in Dusseldorf, taken in March 2026, shows kit boxes and large displays behind plate glass on an ordinary shopping street. The sources read for this chapter do not describe that shop, so the photograph is offered only as evidence that the hobby has a retail presence outside Japan.

A glass shopfront with four tall windows showing Gunpla displays, large model robots and posters, with the word GUNPLA near the door.
Gunpla on a shopping street
A Gunpla pop-up store in Dusseldorf, March 2026, by Kürschner; CC0. Photograph by Kürschner (talk) 16:40, 11 March 2026 (UTC), CC0. Wikimedia Commons, File:Gunpla, Königstraße 10, Düsseldorf, März 2026.jpg.
Look closer: The sources read for this chapter do not describe the shop, so it is offered only as evidence of the hobby's reach.
Image: Kürschner (talk) 16:40, 11 March 2026 (UTC), CC0, via Wikimedia Commons
Imitation

Bootlegs and Where Bandai Went to Court

A popular kit attracts copies. The Gunpla article records that in April 2010 Bandai sued two Chinese toy manufacturers over counterfeit Gunpla kits, seeking 3.69 million renminbi, roughly 540,000 US dollars. It also names bootleg companies, among them Daban, TT Hongli, Model GD, Elyn Hobby and Dragon Momoko, and says that Bandai shut down Dragon Momoko in 2017.

The Bandai article adds a recent warning. On 18 September 2025, it says, Bandai and Bandai Spirits warned that their brand names and logos were being used without permission in AI-generated images of figures and other items on social media. A picture of a toy is therefore no longer proof that the toy exists, and a description that rests on a photograph should say who took it and when.

The same caution applies to older objects. The Collectors Weekly note on vintage robots, which belongs to the tin chapter, gives the example of a Lilliput robot whose reproduction carries a Tin Tom Toy logo in place of the original's KT mark and has no Made in Japan marking. The Myths chapter sets these cases out together. For the mecha toy, the working rule is the same: name the maker, the material, the date of the line and the mark on the box, and say which of them has been checked.

Shelf

Reading a Box Before Opening It

The Gunpla article gives several signals that help to read a box. A kit from 1980 has no grade because the term did not exist until 1990, and the article calls reissues of that line Best Mecha Collection. For the forty-fifth anniversary in 2024, Bandai released a modern Best Mecha Collection Revival of the RX-78-2 in October. The Real Grade RX-78-2 Version 2.0, announced for August 2024, was the first kit to drop the Advanced MS Joint technology altogether. The grade, the scale and the year, printed together, therefore place a kit more reliably than its picture.

Limited editions are named too. The article says clear-plastic, metal-plated or 24-carat gold-finish kits are often prizes at events such as the yearly Bandai Action Kits Universal Cup in Hong Kong, and that some are sold at toy expos, premieres or through web shops, with collaborations including Uniqlo and Hatsune Miku. These are usually priced higher than standard kits, and their value depends on provenance as much as on the plastic.

The house does not hold Gunpla. It does hold the tin robots that came before the metal ones, among them Astro Boy tin toys, the character on whom Bandai's 1963 success was built, and the Collector's Guide explains how such objects are graded. Where the house cannot supply a mecha toy, it says so, and the concierge desk can discuss a particular piece with a collector who has one in mind.

Terms

A Short Glossary of Robot Toys

The terms below are used as the sources use them.

Term Meaning in these sources
Chogokin Super alloy; Popy's name from 1972 for die-cast robot toys; a Bandai trademark.
ST and DX Standard (about 5 inches) and deluxe sizes of chogokin.
Jumbo Machinder Popy's large roto-moulded plastic robots, about 24 inches tall; a trademark often used generally.
Kikaiju A soft vinyl line of Mazinger Z and Kamen Rider V3 enemies, about 20 inches tall.
Shogun Warriors Mattel's late-1970s American and European line of retooled Popy robots.
Godaikin Bandai America's early-1980s line of near-identical chogokin.
Gunpla Gundam plastic models, from Gundam plamo.
Sprue and gate The runner on which parts are moulded, and the small neck joining each part to it.
Poly-cap A soft polyethylene connector used in joints from 1985.
Snap-fit Assembly without glue, standard from 1988.
System Injection Moulding one part in several colours at once.
Grade Bandai's label for a kit's detail and quality, from 1990.
Curiosities

Fun Facts About Robots

  • The robot's cockpit came from a traffic jam, according to the Wikipedia article on Mazinger Z.
  • The first Jumbo Machinder was planned at about one metre tall and cut down for safety.
  • A 40-foot Mazinger Z statue stands in Tarragona, Spain, in a suburb that was never completed, says the same article.
  • Guillermo del Toro has cited Mazinger Z as an influence on Pacific Rim, according to the article.
  • A Gundam kit's colour can be built into the plastic: System Injection moulds several colours in one part.
  • Gunpla appears in other fiction: in Sgt. Frog, Keroro's Gundam addiction stops him from invading Earth, says Wikipedia.
Questions

What People Ask About Robot Toys

People ask what chogokin means. It is the Japanese for super alloy, the fictional metal in Go Nagai's Mazinger Z, and Popy adopted it for a die-cast toy line in 1972. The word is a registered trademark of Bandai, which is why other makers use gokin as an ending.

People ask whether a Jumbo Machinder is metal. It is not. The Wikipedia article says it is roto-moulded PET, the plastic of shampoo bottles, and that its size and lightness were the point. The metal robots are the chogokin, which are much smaller.

People ask whether Gunpla kits are discontinued. According to Wikipedia they almost never are, except for minor problems such as mould damage, and the 1980 kits have been reissued as Best Mecha Collection. A collector is therefore more likely to be choosing between versions than hunting for a single survivor.

In the house

Robots at the Desk

The house does not hold Gunpla or chogokin at the time of writing. It does hold the Showa tin robots that came before them, among them a Nomura Tetsujin 28-go walking tin robot, a Bandai Tetsujin 28 sky rocket tin jet and a grey Astroman walking tin robot with spark action. Stock changes; the shelf page shows what is here now.

Browse the toys shelf

Reader questions

Answered plainly

What was the first chogokin toy?

The GA-01 Mazinger Z, released by Popy in 1972, according to Wikipedia.

How tall is a Jumbo Machinder?

Generally about 24 inches, though not all are; the Kikaiju line stands about 20 inches.

When did Gunpla begin?

In July 1980, when Bandai launched the Gundam plastic model, says Wikipedia's article on Bandai.

What is snap-fit?

Assembly without glue; the first snap-fit Gundam kits came in 1987 and it became standard in 1988.

How many Gunpla kits have shipped?

More than 800 million by September 2024, according to Wikipedia.

Keep reading

Where next

The almanacThe Japanese Toys Almanac, the hub this chapter belongs to.
BridgeThe Play and Living Almanac, the wing neighbour that holds golf and the household machines.
Evidence

Sources and image credits

Last reviewed 28 October 2026. Pictures, where shown, are public-domain or open-access and credited beneath each one.

Looking for a particular tin toy, doll or figure, or a view on one you own? The concierge desk replies within one to three business days.

Browse Retro, Vintage, Antique and Modern Toys · Make a private request