Frédérique Constant: the Heart Beat, the Manufacture Calibres and Japan
In 1994 a young Dutch couple working out of Geneva cut a small round window into a watch dial so that the wearer could see the balance wheel beating. Ten years later, unable to find a movement that put that beating heart where they wanted it, they built their own. Today Frédérique Constant makes more than thirty calibres of its own beside the great houses of Plan-les-Ouates, belongs to Citizen of Tokyo, and has its first boutique in Asia on the ground floor of a Ginza shopping complex.
The short answer
Frédérique Constant is a Swiss watch company from Geneva, begun in 1988 by Peter Stas and Aletta Stas-Bax, two Dutch founders who wanted to make Swiss mechanical watches that more people could afford. The official history dates the first designs to 1988 and the first collection to 1992. Its signature is the Heart Beat, an opening in the dial that shows the balance wheel; its achievement is a manufacture of its own, opened in 2006, that builds movements in-house at a cost target set before the engineering starts. Since 2016 it has been part of Citizen. Readers who want the wider family tree of watch houses will find it in our watch almanac.
| Fact | Detail |
|---|---|
| Founded | 1988 in the Geneva area, by Peter Stas and Aletta Stas-Bax |
| Name | From two great-grandparents, Frédérique Schreiner and Constant Stas |
| Signature | Heart Beat dial opening, first shown in 1994 |
| Manufacture | Plan-les-Ouates, opened 2006, extended to 6,200 m² in 2019 |
| In-house calibres | FC-910 in 2004; the 30th, FC-810, in 2021; more since |
| Owner | Citizen Watch, agreement announced 26 May 2016 |
| In Japan | Distributed by Citizen since 1 August 2017; boutique in Ginza since 2023 |
| Sister brands | Alpina, bought in 2002; Ateliers deMonaco |
Who it is for
The house has never pretended to compete with the old Geneva names on rarity. Its pitch, in Swiss and Japanese pages alike, is a Swiss watch with a real mechanical heart at a level a salaried person can reach. The Japanese site puts it as te no todoku ragujuarī, luxury within reach of the hand. The Citizen Flagship Store in Ginza calls it accessible Swiss elegance. For a reader new to fine watches it is one of the most honest doors into the craft.
The founders and their great-grandparents
The names on the dial
There is no watchmaker called Frédérique Constant. The name joins two great-grandparents: Frédérique Schreiner, born 1881, and Constant Stas, born 1880, who in 1904 founded a company in the Netherlands that made printed dials for clocks. Peter Stas is a fourth-generation descendant of Constant, and a 2001 Swiss trade profile tells the story in exactly those terms. Aletta Stas-Bax put it more simply in an interview in 2018.
"Frederique and Constant are our middle names."Aletta Stas-Bax, interview, 2018 · read
Her full name, she explained, includes Frederique, and Peter’s includes Constant; both were family names, and Constant Stas had made dials for large clocks in Holland (Ethos interview, 2018). The logo is the Stas family crest.
A trip to Geneva
The Japanese brand page says the couple, then around thirty and working in business, were moved by Swiss mechanical watches on a trip to Geneva. A Japanese trade magazine tells a sharper version: Peter, looking in watch shop windows, was surprised by how much a fine Swiss watch cost, and the idea of a house built on reasonable cost was born there. The two versions fit together. The founders loved the craft and thought it cost more than the people who would love it most could pay.
Thônex, Carouge, Chêne-Bourg and Plan-les-Ouates
The Japanese history places the founding in 1988 in Thônex, on the edge of Geneva. The official history has the designers working from 1988, a first collection in 1992 built from Swiss movements and assembled by a Geneva watchmaker, a move to Carouge in 1997 and to Chêne-Bourg in 2000. The 2001 profile records the same moves and counts more than 40,000 watches a year by then. The last move, to a purpose-built manufacture in Plan-les-Ouates, came in 2006; the neighbours there include Patek Philippe and Vacheron Constantin.
The window in the dial
1994, at twelve o’clock
The first Heart Beat came in 1994. An aperture at twelve o’clock showed the heart of the movement, the balance wheel swinging back and forth, and it became the house signature. The Japanese site calls it the world’s first open-dial watch. That is the brand’s own claim, and we print it as one.
Followers, and the move to six
It was copied. A Japanese interview with the house tells how the Heart Beat drew many followers, and how the team, unwilling to be one of many, wanted the balance at six o’clock instead. The movements on the open market mostly had the balance under twelve, so the only way to put it at six was to design a movement of their own. This is the hinge of the whole story. A brand built on bought-in movements became a manufacture because of where it wanted a hole in the dial.
One heart and two
The Heart Beat now runs through the range: on round Classics, on the rectangular Carrée, and on ladies’ models such as the Ladies Automatic Double Heart Beat, where two overlapping heart-shaped windows show the balance. The 2026 Japanese site leads with a new Double Heart Beat for women and, for the third anniversary of the Tokyo boutique, a Japan-only Carrée Automatic Heart Beat.
The house’s own short film, made in 2013 for ten years of the Heart Beat Manufacture, shows the movement and the workshop that came out of that decision.
Becoming a manufacture
Students, a prize-winner and Pim Koeslag
Peter Stas came from outside the trade. The Japanese account says he asked watch-school students who visited the company whether any of them would help, and that Pim Koeslag, a prize-winning master watchmaker, joined the effort. The official history has Koeslag arriving in 2001. In 2004 a team of eight was working with the École d’Horlogerie de Genève, the École d’Ingénieurs de Genève and the Horloge Vakschool Zadkine, with fourteen outside specialists chosen for the components.
The FC-910 in numbers
The first calibre, FC-910, appeared in 2004. It is hand-wound, 30 mm across and 3.35 mm thick, with 71 parts, 17 jewels, a balance at 4 Hz and 42 hours of reserve, and the balance sits on the dial side at six so that the Heart Beat shows it directly. Fine regulation could be done from the dial side, and put the work at two and a half years; the Japanese history says three.
Plan-les-Ouates and the workshops
The manufacture opened in Plan-les-Ouates in 2006 and was enlarged in 2019 to 6,200 m², with a visitor museum called the Manufacture Experience. The official manufacture page describes four workshops by number. T0 machines the brass plates and bridges on CNC machines before rhodium plating; T1 assembles the in-house movements, with jewelling, oiling and balancing done largely by hand; T2 is case assembly; T3 is quality control, where every watch, quartz or mechanical, is tested for function and water resistance, and mechanical watches also for rate, amplitude and power reserve.
What in-house means here
In-house at Frédérique Constant has always meant something specific. Aletta Stas-Bax said in 2018 that the house conceives its movements itself, uses contractors for high-volume parts, and buys in items such as screws and balance wheels; in-house movements were then about a quarter of turnover (Ethos interview). The rest of the range uses Swiss movements from outside, which is why the calibre number matters.
The calibres, read in families
The official calibre page lists every in-house movement with its year, size, parts, jewels, beat and reserve; the Japanese site keeps a parallel timeline. Most share a 30 mm base, 28,800 vibrations an hour and, until 2024, 38 to 42 hours of reserve. The table picks the landmarks.
| Calibre | Year | What it does |
|---|---|---|
| FC-910 | 2004 | Hand-wound Heart Beat; 71 parts, 17 jewels, 42 h; the first calibre |
| FC-930 | 2006 | First automatic Heart Beat; 27 jewels, 42 h |
| FC-980 | 2008 | Tourbillon at six with silicon escape wheel; individually numbered |
| FC-700 | 2009 | Maxime, the first of the FC-7xx series; 26 jewels, 38 h |
| FC-718 | 2012 | Worldtimer; every function set with the crown |
| FC-945 | 2014 | Heart Beat moonphase with silicon escape wheel, anchor and roller |
| FC-724-C | 2015 | Zodiac: a 24-hour display drawn with the animals of the Eastern zodiac |
| FC-775 | 2016 | Slimline Perpetual Calendar; 191 parts |
| FC-760 | 2017 | Flyback chronograph; 233 parts, 32 jewels |
| FC-750 | 2018 | Hybrid: mechanical movement with a connected module |
| FC-975 | 2018 | Tourbillon perpetual calendar for the thirtieth anniversary; 250 parts |
| FC-810 | 2020–21 | Slimline Monolithic; 40 Hz, 80 h, 19 jewels |
| FC-735 | 2023 | Power reserve, big date and moonphase |
| FC-706 and FC-716 | 2024 | Classic Date and Moonphase Date; 72 h |
The FC-7xx family
The seven-hundreds begin with the 2009 Maxime, FC-700. The series grew to include a power reserve, a worldtimer, moonphases, a perpetual calendar, a flyback chronograph and the hybrid, many of them with every function set from the crown alone (calibres).
The 72-hour generation
In 2024 the Japanese timeline announced FC-706 and FC-716, using more than ninety per cent of the parts of FC-710 and FC-715 but with a barrel 18 per cent larger and a mainspring 31 per cent longer, for 72 hours of reserve and a five-year international warranty. FC-776 followed in 2025, and in 2026 the Tokyo boutique listed a new Classic Worldtimer Manufacture, 40 mm with 72 hours, under a reference beginning FC-719 (Boutique Tokyo). A watch that stops over a weekend on the dresser is one of the small annoyances of an older automatic; the new generation answers it.
Silicon, early and then all the way
2008, a silicon escape wheel
Silicon parts in the escapement do not need oil, resist magnetism and can be cut to shapes steel cannot take. In 2008 the house put a silicon escape wheel into its first tourbillon, FC-980. Silicon was then, by the maker's own account, something only a few top makers used. Production of silicon escape wheels dates to February 2007. By 2014 the FC-945 had a silicon escape wheel, anchor and roller (calibres).
The Slimline Monolithic, FC-810
The bigger step came in 2021. The Slimline Monolithic Manufacture replaced the balance wheel, hairspring, pallet fork and their companions with a single silicon oscillator, about 26 components replaced by one, beating at 40 Hz with 80 hours of reserve; it was the thirtieth in-house movement. The oscillator is 9.8 mm across and 0.3 mm thick, cut by deep reactive ion etching, with an amplitude of about six degrees against roughly three hundred for a conventional balance, and the gear train gained an extra wheel.
How forty hertz looks
At 288,000 vibrations an hour the seconds hand does not tick; it advances eighty times a second and glides. The Japanese history puts the speed at ten times that of an ordinary watch. The house regulates the movement with a laser-controlled high-speed camera capable of firing up to 250,000 times a second, and the first editions were 810 pieces for each steel dial and 81 in gold.
A Dutch oscillator, and a cousin at Zenith
The Japanese site calls the FC-810 a world first. The fuller picture is more interesting. The oscillator was developed with Flexous, a Dutch specialist founded in 2012 within a technology incubator in Delft, the same firm behind the oscillator in Zenith’s Defy Lab and Defy Inventor; the FC-810 is a miniaturised take on that system, at 40 mm against the Zenith’s 44. There are other flexure oscillators, from Parmigiani and Ulysse Nardin as well as Zenith, and the novelty is usually located in the anchor, integrated into the flexures for the first time. Escapement magazine framed it in the line of Harrison and Breguet, as nearly thirty escapement parts of a roughly 130-part movement reduced to one. Our Zenith guide tells the Defy side of the story.
Quartz, smart and hybrid
The Hybrid Manufacture, 2018
In 2015 the house launched what it calls the first Swiss horological smartwatch, an analogue dial over a quartz calibre with a connected module. The 2018 Classic Hybrid Manufacture put a mechanical movement, FC-750, together with a connected counter at twelve for activity and sleep tracking; Aletta Stas-Bax added that it reads analytics from the mechanical movement and tells the owner when a service is due (calibres; Ethos interview). The official history calls it a combination of quartz and mechanical for the first time in watchmaking. For a collector it is a curiosity of its decade, and the connected half depends on an app; ask whether the module still pairs before choosing one.
Moneta, quartz and the first solar calibre
Quartz has always been part of the range. The 2024 Classic Moneta Moonphase, 37 mm and 7.6 mm thick with a coin-edge flange and quartz calibre FC-206, was launched in Japan in 2024; two years later the Japanese site called it one of the most chosen collections in the line-up. In September 2026 the Japanese site announced a hand-wound Moneta on a movement by La Joux-Perret, mother-of-pearl moonphase dials and the Moneta Solarmeter, which it calls the brand’s first solar calibre. Quartz is not a lesser watch here; it is half of the honest promise, and the first quartz wristwatch was itself a Japanese watch, as our Astron history tells.
The Highlife, 1999 and 2020
An integrated bracelet, twice
The Highlife first appeared in 1999 with an integrated strap and bracelet and a distinctive case. In 2020 the house brought it back as a modern sports watch: a 41 mm barrel-shaped case, a dial patterned with a globe grid, and a bracelet or strap that changes without tools, with a spare rubber strap in every box and 50 metres of water resistance. The Japanese history describes the same revival, with the globe motif as its theme.
Why then
Niels Eggerding, the managing director, was candid. Two years earlier, he said, the house had found that 60 to 65 per cent of European sales in the upper bracket were integrated-bracelet designs, and it wanted a place in that market with a design of its own. The 2020 launch ran to ten models across three types and a limited collaboration with the collector group RedBar; the cases are about 12 mm thick. The category goes back to Gérald Genta’s Royal Oak of 1972, traced in our Royal Oak guide; Tissot’s PRX took the same road at a different level, as our Tissot guide explains.
Three movements, one case
The 2020 range divides by movement. The Highlife Automatic COSC uses calibre FC-303, based on the Sellita SW 200-1 and certified as a chronometer; the Highlife Heart Beat uses FC-310, also on the Sellita base; and the Highlife Perpetual Calendar Manufacture uses the in-house FC-775.
Classics, Carrée, Runabout and Worldtimer
The Classics
Classics is the house’s broad dress line, round models and square ones such as the Classic Carrée Automatic Heart Beat; the Manufacture models, with decorated movements behind see-through backs, sit beside them. Most Frédérique Constant watches seen in Japanese collections are Classics or Heart Beats, and that is where a first watch from this house usually begins.
Carrée, the square
The Japanese site explains that Carrée is French for square and that the collection takes its cue from the Art Deco of the 1920s and 1930s (Frédérique Constant Japan, home; brand page). The rectangular case is a good fit for a slim wrist and a shirt cuff, and the Heart Beat sits well in it.
Runabout and Vintage Rally
Two lines borrow from engines. The Runabout, from 2009, takes its name and mood from the wooden motor launches of the 1920s, and in 2013 the house began a partnership with the Riva Historical Society, which looks after those wooden boats. The Vintage Rally began in 2004 with a partnership with the British car marque Austin-Healey.
The Worldtimer
The Classic Worldtimer Manufacture of 2012 shows the time in 24 cities and sets every function from the crown alone (official history; calibres). In 2026 the Japanese site marked the Worldtimer’s fifteenth year at Watches and Wonders, and the new 72-hour version followed. For a traveller it is the most useful complication the house makes.
Geneva and Tokyo: the Citizen years
26 May 2016
On 26 May 2016 Citizen Watch Co. announced an agreement to acquire Frederique Constant Holding SA, with its brands Frédérique Constant, Alpina and Ateliers deMonaco, as part of its plan to build a group of brands at different levels; the existing management would stay. The law firm that advised Citizen recorded that the deal covered all the shares and that its value was not disclosed.
"We see the opportunity of Swiss-Japanese partnership to develop and market Accessible Luxury watches for the 21st century and beyond."Peter Stas and Aletta Stas-Bax, Citizen announcement, 2016 · read
Toshio Tokura, then Citizen’s chief executive, said in the same announcement that sales would grow through Citizen’s channels, particularly in Japan and the United States. The release counted nineteen in-house calibre versions since 2004. Our Citizen guide tells the Tokyo side of the family.
What stayed in Geneva
Design, movements and assembly stayed in Plan-les-Ouates. The founders remained in the business; the official history records Niels Eggerding, who had joined in 2012 and led sales from 2014, as managing director from 2018, and the extension of the manufacture followed in 2019. The Japanese trade view is that the house still fixes the cost of a watch before development begins and works backward from it.
Frédérique Constant in Japan
Japan matters to this house twice over: it is a market, and since 2016 it is home to the parent company. Why Japan suits a careful buyer of watches like these is the argument of our essay on why Japan is the finest market for pre-owned luxury.
The agent years, 1999 to 2017
GM International was the sole Japanese agent from 1999 until the brand joined Citizen. A Tokyo technology magazine, reporting the handover in August 2017, gives the end date as 31 July 2017. The same entry notes the house’s fondness for guilloché and blued hands on most of its watches, which is a fair description of what Japanese buyers first met.
Citizen from 1 August 2017
From 1 August 2017 Citizen took over sales, marketing and the repair desk in Japan. At the launch Tokura said that owning the house strengthened Citizen at the upper end and promised Japan-only models; Peter Stas reported that in North America, where seventeen of his staff had joined some five hundred Citizen staff from 1 January 2017, sales were already up 30 per cent on the year. Development, design, parts and final assembly of the calibres stay in Geneva, so the watches leave as Swiss made.
The boutique in Ginza
On 20 October 2023, for the thirty-fifth anniversary, the house opened Frédérique Constant Boutique Tokyo, its first boutique in Japan and the first in Asia. It sits inside the Citizen Flagship Store Tokyo on the ground floor of Ginza Six, at Ginza 6-10-1, with a repair workshop on site; the shop claims the largest range in Japan and sells some models only there (Boutique Tokyo). The street around it has a long watch history of its own, told in our Ginza and the watch.
Japan-only and Japan-first
The promise of Japan-only models has been kept. In 2026 the boutique launched the Classic Ladies Automatic Double Heart Beat in Tokyo ahead of other markets, and for its third anniversary a Japan-only Classic Carrée Automatic Heart Beat (Boutique Tokyo; Frédérique Constant Japan, home).
The Eastern zodiac
One manufacture calibre speaks directly to East Asia. The Zodiac Manufacture of 2015, calibre FC-724-C, shows a 24-hour display drawn with the animals of the Eastern zodiac.
Reading a reference
The calibre is in the number
The Japanese support page gives the one rule the house publishes: on the caseback, “FC-” and the three digits after it are the calibre number, so a reference beginning FC-200 has calibre FC-200. The remaining letters and figures change with dial, case and strap; the house has not published a key to them, and we do not guess.
| Reference | Calibre | Watch |
|---|---|---|
| FC-930EM3H6 | FC-930-3 | Classic Heart Beat Manufacture, 39 mm, 930 pieces |
| FC-719BLW3H6 | FC-719 | Classic Worldtimer Manufacture, 40 mm, 72 h |
| FC-301SAL3B6B | FC-301 | Classic Premier, automatic |
| FC-206… | FC-206 | Classic Moneta Moonphase, quartz, 37 mm |
| FC-303… | FC-303 | Highlife Automatic COSC, Sellita base |
| FC-810… | FC-810 | Slimline Monolithic Manufacture, 40 Hz |
Manufacture or not
There is a practical test: in-house watches carry “Manufacture” in the model name, and their calibres are in the FC-9xx, FC-7xx and FC-810 series. The FC-3xx automatics are built on Swiss movements from outside; the Sellita SW 200-1 is the base of FC-303 and FC-310. The Japanese support page groups the user manuals of FC-301, 303, 310, 312, 313 and 315 with FC-706, 710 and 723, so a shared manual says nothing about who made the movement (support). Quartz models such as the Moneta carry FC-2xx numbers, as with FC-206.
Condition, papers and service
Warranty and the card
In Japan a new Frédérique Constant comes with a two-year international warranty, extended by a year when the owner registers online. After the warranty, repair and maintenance are offered at special rates only to owners who show the AUTHENTICITY card issued by an authorised Japanese retailer, and the page asks owners to keep it. Quartz buyers get one free battery change within a year, in Japan only. Repairs go through Citizen Customer Service in Takenotsuka, Adachi, in Tokyo, which also offers polishing; watches bought at Citizen outlet shops are serviced at normal rates.
That makes the card part of the watch. Our guides to box and papers and to documentation as value explain why a complete set is worth more than the sum of its parts in Japan.
What to check
| Point | What to look for |
|---|---|
| Caseback | Calibre number matches the dial: FC-9xx, FC-7xx or FC-810 for a Manufacture |
| Heart Beat | Balance swings with full, even arcs; no dust under the opening |
| Crown functions | Worldtimer and Slimline calibres set everything from the crown; test each position |
| Plating | Plated cases wear at edges and clasp; ask for a light clean, not a polish |
| Strap system | Highlife quick-release pins work, and the spare rubber strap is present |
| Hybrid and smart | The connected module still pairs with the current app |
| Papers | International card, Japanese AUTHENTICITY card, box and manual |
We grade by the ranks set out in our guide to Japanese condition ranks and our grading guide, and every watch we offer is covered by our authenticity guarantee. How Japanese owners look after watches between wearings is set out in kept in the box.
Where the records disagree
A young house with many retellings has collected small contradictions. None of them changes what a watch is, but each is a trap for a careless description.
| Point | One account | Another |
|---|---|---|
| First Basel fair | 1995 | 1997 |
| First collection | Six models, 1992 | The 18th Century Collection, 1992 |
| FC-910 development | Two and a half years | Three years; or from 2001 with three other brands |
| Koeslag joins | 2001 | 2002 |
| Ateliers deMonaco | 2008 | 2009 |
| FC-810 year | 2021 | 2020 |
| Worldtimer | 2012 | Fifteenth year in 2026 |
| Manufacture extension | 2019 | 2018 |
| In-house calibres | 19 (2016) | 30+; 33 |
| Outside movements | Sellita | ETA on lower models |
| “World first” (Heart Beat; FC-810) | The brand’s claims | FC-810 oscillator made with Flexous, as in Zenith’s Defy |
| Eggerding’s 2018 title | Managing director | Chief executive |
Some of these are not contradictions at all. Calibre counts grow every year, and a 2016 count of nineteen and a 2024 count of thirty-three can both be right. Where they are genuine we follow the official history and name the other version. The “world first” claims for the Heart Beat, the 2015 smartwatch and the FC-810 are the house’s own; the Monolithic in particular shares its oscillator principle with Zenith, as above.
The case against
There is a fair case against. The history is short, and most of it is the founders’ own telling. The house name is invented, and its oldest date, 1904, belongs to a dial company in the Netherlands, not to a watch. Many watches in the range use the same Swiss base movements as dozens of other brands. And for a collector chasing scarcity there is very little: output passed 40,000 watches a year by 2001 and is put at about 120,000 in 2024, and limited editions of 810 or 930 are not rare in the way the word suggests.
The answer is that rarity was never the promise. The house set out to put real watchmaking within reach and did it, with a manufacture of its own, early silicon and a genuinely new oscillator, at a level where few rivals build their own movements. Japan has a long habit of respecting a maker that does exactly what it says, which is part of why the Grand Seiko story is read so closely here. For the reader who wants a mechanical watch from Geneva with an honest heart, that is enough.
Questions readers ask
Is Frédérique Constant a real Swiss manufacture?
Yes, for the Manufacture line. The house designs and assembles its own calibres in Plan-les-Ouates, and has since 2004. Other models use Swiss movements from outside, such as the Sellita base of FC-303.
Is it Japanese now?
It is owned by Citizen of Tokyo since 2016, but design and manufacture remain in Geneva and the watches are Swiss made.
What is the Heart Beat?
An opening in the dial, first shown in 1994, that lets you see the balance wheel beating. On Manufacture calibres it sits at six o’clock.
How do I tell a Manufacture model from the caseback?
Read the three digits after “FC-”: they are the calibre (support). FC-9xx, FC-7xx and FC-810 are in-house; FC-3xx are automatics built on outside bases; quartz models such as the Moneta use FC-2xx numbers.
Can it be serviced in Japan?
Yes. Citizen Customer Service handles repairs, and the Ginza boutique has a workshop on site. Keep the Japanese AUTHENTICITY card for special rates after the warranty (support; Boutique Tokyo).
Looking for a Heart Beat Manufacture, a Slimline Monolithic or a Japan-only reference with its card? Ask the Hunting Salon, or browse our collectible watches.
Further reading
- Swatch, 1983, for the other Swiss answer to the cost of a good watch
- Collectible watches, for how we choose the watches we offer
- Our watch almanac, for where a Geneva house of 1988 sits among the groups
- Vintage Citizen, for the Japanese owner since 2016
- Zenith, for the Defy Inventor and the Flexous question
- Tissot PRX, for the integrated-bracelet revival beside the Highlife
- Maurice Lacroix, for the Calypso, the Aikon and the Masterpiece calibres
- the Bulova guide, for the Accutron tuning fork, the Precisionist and the American clock
- Oris, for Hölstein's Big Crown, the Pointer Date and the Divers Sixty-Five
References
- Frédérique Constant, history
- Frédérique Constant, calibres
- Frédérique Constant, the manufacture
- Frédérique Constant Japan, home (in Japanese)
- Frédérique Constant Japan, brand (in Japanese)
- Frédérique Constant Japan, history (in Japanese)
- Frédérique Constant Japan, calibre timeline (in Japanese)
- Frédérique Constant Japan, the manufacture (in Japanese)
- Frédérique Constant Japan, support (in Japanese)
- Frédérique Constant Japan, Classic Moneta Moonphase, 2024 (in Japanese)
- Frédérique Constant Japan, Moneta news, 2026 (in Japanese)
- Frédérique Constant Boutique Tokyo (in Japanese)
- Citizen Flagship Store Tokyo
- Citizen Watch, acquisition announcement, 2016
- Baker McKenzie, Citizen acquisition, 2016
- ASCII, Citizen begins Japan distribution, 2017 (in Japanese)
- Europa Star, Frédérique Constant profile, 2001
- Europa Star, Heart Beat Calibre FC 910, 2004
- Ethos, interview with Aletta Stas-Bax, 2018
- Monochrome, Highlife collection, 2020
- Watchonista, Highlife, 2020
- Hodinkee, Slimline Monolithic Manufacture, 2021
- Monochrome, Slimline Monolithic Manufacture, 2021
- Escapement, the Monolithic, 2021
- webChronos, Classic Heart Beat Manufacture, 2023 (in Japanese)
- webChronos, Frédérique Constant brand page (in Japanese)
- Wikipedia, Frédérique Constant
- Japanese Wikipedia, Frédérique Constant (in Japanese)
- Frédérique Constant, ten years of the Heart Beat Manufacture, 2013 (YouTube)
The Japonista Curation and Concierge Team, Tokyo, Japan