The Collector's Guide to Condition, Boxes and Grades
Toys Almanac · Reading an Object
The Collector's Guide to Condition, Boxes and Grades
Two dealers can describe the same toy in different words and both be honest, because there is no single scale for condition. This guide sets out the scales that are published, what the sources say about boxes, markings, repainting and care, and a checklist that lets a reader compare any description with any other.
Fact sheet
At a glance
- No single scale. Mandarake grades from 10 to 1, a UK dealer uses overlapping bands, and AFA uses a modern and a standard scale. A grade means little without the name of the scale.
- The box is part of the toy. The Journal of Antiques says original boxes are critical for battery toys, and that in some cases a box in good condition is worth twice the toy.
- Repainting lowers value. The same article says repainting lowers value and that collectors should watch closely for touch-ups.
- Leave minor damage alone. The founder of the Brighton Toy and Model Museum advises that small chips and abrasions should be left as they are.
- Document what was done. Recreating a missing part can be seen as faking if it is not documented, the museum's article warns.
A Grade Is a Sentence, Not a Number
Condition is a language, and like any language it has dialects. A collector who reads that a toy is a 7 has learned very little until he knows whose 7 it is. This chapter therefore begins with a plain rule: a grade should always be given with the name of its scale, and with the facts that produced it. Where the facts are given in words and photographs, the grade can be checked. Where only a number is given, it can only be believed.
The sources read for this guide are of three kinds. Some are dealers who publish their own scales, and these are the best evidence of how a grade is used. Some are museum and conservation sources, which say what damage is, how it happens and what should not be done to an object. The third kind is a collector's or journalist's account of the market, which says what buyers value and what has changed. None of them is a complete guide, and the chapter says where one is silent.
The house does not publish prices in this chapter and does not change the price of any piece in it. The purpose is to make a description comparable. A buyer who knows how to read condition can compare a dealer's description in Tokyo with one in Brighton, and a collector who knows how to write condition can describe a toy to a stranger without needing to be believed on trust.
Three Ways to Count from Ten
Mandarake, the Japanese retailer of collectibles, publishes a ten-point scale that, according to its own help page, has applied to all categories since May 2024. Ten is Mint, defined as the best possible condition the item can be in. Nine is Excellent, with minor imperfections that do not significantly affect appearance or function. Eight is Great, well maintained and fully functional with minor wear. Seven is Good, usable and functional but with some noticeable wear. Six is Average, functional but with significant wear and cosmetic flaws, and five is Decent, with moderate wear. Four is Fair, three Acceptable and heavily worn, two Mediocre and one Poor, heavily worn, damaged or non-functional.
The page adds a caution that is easy to miss: grades two and one carry the most risk, and buyers should expect limitations and possibly additional repair or care. It also gives no grading system for boxes or packaging. That is a significant omission for a collector of tin and vinyl, since the box is often a separate object, and it means that a Mandarake grade describes the toy and leaves the box to the dealer's words.

One of the Mandarake stores in Nakano Sun Mall; photographed by fletcherjcm; CC BY-SA 2.0. Photograph by fletcherjcm, CC BY-SA 2.0. Wikimedia Commons, File:Mandarake (4970180671).jpg.
Look closer: Mandarake's help page gives its scale. The photograph shows only the shopfront, and the sources read for this chapter say nothing of what this branch grades.
Image: fletcherjcm, CC BY-SA 2.0, via Wikimedia Commons
A UK dealer of vintage toys publishes a different ten-point scale. Its top is 10.0, perfect with no noticeable defects, and its next band, from 8.0 to 9.0, is excellent to near mint, with only a few minor marks noticeable on close inspection. Bands from 7.0 to 8.0 and 6.0 to 7.0 describe very good and good, used condition, 5.0 to 6.0 is average for its age, 3.0 to 4.0 is fair and clearly used or played with, and 1.0 to 2.0 is poor, rarely sold except for very rare or old toys. The page's bands overlap at whole numbers, for example at 8.0, and it does not say how to resolve this. It says each product page gives a detailed description with all known defects and detailed photographs, and that the dealer offers a money-back guarantee on every vintage item.
Taken together, the two pages show how much a number depends on its home. Mandarake's scale names each step, so a reader can see what a seven means to the shop. The UK dealer's scale gives bands, so a reader must look at the description to see where in the band the toy falls. Neither is wrong. The honest practice is the one the UK dealer itself follows: let the number summarise and let the words and photographs prove.
| Scale | Top and bottom of the scale | What the page says about boxes |
|---|---|---|
| Mandarake, from May 2024 | 10 Mint to 1 Poor, in ten named steps | The page gives no grading system for boxes or packaging. |
| A UK dealer of vintage toys | 10.0 Perfect to 1.0 to 2.0 Poor, in bands that overlap at whole numbers | The page says nothing about boxes; each product page gives a description and photographs. |
| AFA, as described by a dealer of graded toys | A ten-point modern scale for toys from 1995, and a standard scale for older toys | Toys are sealed in clear acrylic cases; grading is by appearance alone. |
Words That Carry Evidence
A description can be built from a small set of words, each of which is a claim that can be checked. Original means that the part or finish is as the maker made it. Restored means that something has been repaired or replaced, and the description should say what. Repainted means that paint has been added over or in place of the original, and it should say where. Working means that the mechanism runs, and the description should say how it was tested, with which power source and for how long. None of these is a grade. They are the facts from which a grade is made.
The Journal of Antiques is blunt on one of them: repainting lowers value, and collectors should watch closely for touch-ups. The article also records the range of tastes in the field. Some collectors focus only on toys with bright, graphic boxes, and few of the Japanese box artists are known by name. Some tin collectors exclude any toy with plastic parts, while others accept up to about 15 per cent plastic. A good description therefore names the materials, because the same toy may be a prize to one buyer and unacceptable to another.
Words also need dates. The article places the heyday of Japanese tin toys at about 1952 to 1962, and says that tin fell out of favour after 1962 as plastic became the preferred toy material. Early 1950s toys often have celluloid windshields and other parts, and later toys usually have plastic parts. By the mid 1950s, it says, makers had replaced many wind-up mechanisms with miniature battery motors. A description that names a material and a mechanism therefore gives the reader two ways of placing the toy in time.
Why the Carton Counts
The box is the best-documented part of a toy's history. The Journal of Antiques says original boxes are critical for battery-operated toys, because they often hold the battery insertion instructions, the operating directions, the toy's name and the maker's name, and a parts list. In some cases, it says, a box in good condition is worth twice the price of the toy itself, and a working toy with good paint in its original box can command far more than a non-working, worn toy without one.

The lithographed box of a Masudaya battery tank. Photograph by D J Shin, CC BY-SA 3.0. Wikimedia Commons, File:Masudaya Battery Powered Army Tank M-99 Tin Toy Box Art.jpg.
Look closer: The box carries the toy's name and its power source, which the Journal of Antiques says boxes often record, along with instructions and a parts list.
Image: D J Shin, CC BY-SA 3.0, via Wikimedia Commons
The box also tells a story of its own. Justin Pinchot, interviewed by Collectors Weekly, notes that early robot boxes often showed robots stomping through cityscapes, a reference, he says, to the atomic bombs. Few of the Japanese box artists are known by name, the Journal of Antiques adds, and boxes often carry the names of the American importers, such as Franconia and the Illfelder Toy Company, which was founded in 1856. The chapter on makers and brands sets out how to read those names.
A box can also mislead. The Journal of Antiques warns that marks sometimes conflict with the importer's name on the box and that different factories used different marks, so a box does not by itself prove which maker built the toy inside it. A reader's comment beneath the Collectors Weekly article says reproduction boxes may say Made in China, name a maker called Ha Ha Toys, or carry a number beginning ME. A comment is not evidence on its own, and the chapter reports it only as a lead for further checking. The sensible description says whether the box is original, whether it belongs to that toy, how it is damaged, and how that was established.

Box art for a Billiken Shokai wind-up Robby the Robot with a disintegrator ray gun, a modern tin version. Photograph by D J Shin, CC BY-SA 3.0. Wikimedia Commons, File:Billiken Shokai Tin Wind Up Robby the Robot with Disintegrator Ray Gun Olive Green Version Box Art.jpg.
Look closer: This box belongs to a modern production. Placing it beside a 1950s box shows how much the printing has to be read, not just admired.
Image: D J Shin, CC BY-SA 3.0, via Wikimedia Commons
Two photographs show the difference between the original and the later edition. The Commons images on this page include the box of a Horikawa Monster Robot with an importer's sticker at the foot, the box of a reproduction of the Mr. Atomic robot printed with Wind-Up Action and Made in Japan but no maker's name, and the box of a modern reproduction series in the Osaka Tin Toy Institute's collection. The last two are reproductions, and the photographs are labelled so.
Maker's Mark, Importer's Label
The Journal of Antiques names several marks that appear on Japanese tin toys, among them Alps, EC, MM, M-T Co., MS, MS-Co., HTC, TM and TN. It describes Alps Shoji of Tokyo, founded in 1948, as a well-known maker whose toys are generally well marked. It also records the difficulty. Many toys have no maker mark, and some have marks only on the box. Some marks identify the distributor or marketing company, not the manufacturer, and different factories used different marks.

Mini Shooting Giant Robot, sold under the Rocket USA name, with Masudaya named in the file title. Photograph by D J Shin, CC BY-SA 3.0. Wikimedia Commons, File:Rocket USA – Masudaya – Tin Wind Up – Mini Shooting Giant Robot (ミニ シューティング ジャイアント ロボット) – Gang of Six!! – Back Side.jpg.
Look closer: Marks are often on the back or the underside. Photograph both before describing a toy.
Image: D J Shin, CC BY-SA 3.0, via Wikimedia Commons
The practical lesson is to record each name on the object and say what it is. The chapter on makers and brands distinguishes four kinds of name: the maker's mark, the importer's name, the licence holder's name and the brand name. A description that merges them invites error. The safest wording is a list: the marks seen, where each was seen, and which of them the dealer believes to be the maker's.
The same discipline applies to vinyl and to kits. A foot stamp, a sticker, a box printing or a moulded logo each says something different, and the chapters on soft vinyl and on Gunpla give examples of reissue marks that can be confused with the marks of the originals. Where a mark has been rubbed off, the description should say so, because Pinchot says that some dealers rub off maker's marks to pass reproductions off as originals, and a missing mark is therefore a reason to ask more questions and not fewer.
Rarity Numbers and Counting Actions
The Journal of Antiques describes two scales that sit beside condition. The first is a rarity scale for battery-operated toys that runs from number 1, very common, to number 10, very scarce, with prices generally rising with the number. The article says rare toys are rare for one of three reasons: limited production, fragility or heavy collector demand. The second counts actions. A toy with three or more movements is a major action toy and one with fewer is minor, and the article lists walking, rolling, turning, spinning, smoking, blowing air, pouring, lighting, sounds, bouncing and facial movement among the actions, saying that more actions generally mean higher value.
These scales help a reader to separate three questions that are often mixed. How scarce is the model? How elaborate is the mechanism? And what condition is this example in? A scarce, elaborate robot in poor condition is a different object from a common, simple one in mint condition. Neither the rarity number nor the action count appears in the house's own descriptions as a grade, but each is a fact that a description may state.
The article also sets out the other side of rarity. It says medium-sized transitional toys are often the rarest and most desirable, since early toys tended to be smaller and larger versions came later, and that Japan reportedly made 95 per cent of the world's battery-operated toys in what it calls their golden age. Both statements are reported as the article gives them, and the chapter on tin plate discusses how sources differ on the dates of the period.
How Tin Goes Wrong
Leaking batteries were a hazard from the start. The Journal of Antiques says that leaking battery acid destroyed many toys, and advises collectors never to store toys with batteries installed. Pinchot adds a warning about the hands of the collector. He says fingerprints should not be left on robots because the acid in finger oils will etch them, and that he runs his battery robots and replaces their batteries every couple of months, which suggests an attitude of regular, careful use and not of sealed storage.
Museum guidance gives the general principles for metal. The Scottish Museums factsheet on metals care says dry conditions are below 65 per cent relative humidity and that general storage should be kept stable and low. It advises wearing gloves whenever handling metal because fingerprints can leave uneven, disfiguring tarnish, moving items in a box or tray, and minimising dusting with a clean, soft cotton cloth or soft brush. It states that corrosion needs moisture and salts, so dry, clean conditions are the best prevention, and says tin forms a thin protective oxide that can stay bright for years. The factsheet does not address tinplate specifically, and the guide does not pretend that it does.

The Masudaya battery-powered tank M-99, seen head-on against a pale studio background. Photograph by D J Shin, CC BY-SA 3.0. Wikimedia Commons, File:Masudaya Battery Powered Army Tank M-99 Tin Toy Front.jpg.
Look closer: Rubber tracks perish and paint rubs at the edges of the hull. A description should say what has been replaced.
Image: D J Shin, CC BY-SA 3.0, via Wikimedia Commons
The factsheet also gives two cautions that apply to any old object. Never remove patinas, it says, and polishing and rust conversion are treatments on which a conservator should be consulted. The Journal of Antiques, writing for collectors, suggests that a quality car wax can add shine to metal parts if tested first in an inconspicuous spot. The two pieces of advice differ in tone, and a collector who owns a valuable piece should follow the more cautious.
Chris Littledale of the Brighton Toy and Model Museum adds a point about construction. Lithographed toys have thinner paint and lighter tinplate than painted ones, he says, so they are more vulnerable and can be ruined by damp storage, and poor storage in attics, sheds or cellars often does more harm than original play. That is a useful reminder that condition is not only the history of a child's use, but also the history of the years since.
- Never store a battery toy with batteries inside.
- Keep metal dry; the Scottish Museums factsheet gives below 65 per cent relative humidity.
- Handle with clean gloves; finger oils can etch a surface.
- Do not remove patina or polish a valued piece without a conservator's advice.
- Avoid damp rooms, attics, sheds and cellars.
What Restoration Changes
Littledale, who has worked as a restorer for forty years, sets out a principle that every collector can adopt. Minor damage, such as small chips, light paint loss, abrasions, shallow dents and slight discolouring, should be left as it is, and the object cleaned gently with small brushes, cotton buds and paper towel, then damp-cleaned with cold water and a little detergent. Serious damage, including heavy paint loss, flaking, corrosion, structural damage and missing parts, should be left to a professional restorer.
He is precise about the risks. Water must be cold, since warm water can cause blooming or milking of the finish, and objects should not be soaked unless a proper professional drying enclosure is available. Restoration can strip and replace original paint, build up and recolour surfaces, add ageing so that new work blends with the old, and recreate missing parts such as funnels, masts or flags in matching material and paint. The restorer must judge where to stop, he says, since over-restoration can be as damaging as neglect.
Exterior of the Yokohama Museum of Tin Toys. Photograph by 妖精書士, CC BY-SA 3.0. Wikimedia Commons, File:Tintoy museum.JPG.
Look closer: A museum is where a toy is kept unrestored on purpose. The sources read for this chapter do not describe this museum's restoration practice.
Image: 妖精書士, CC BY-SA 3.0, via Wikimedia Commons
The article's point about honesty is the one that matters most to a description. Recreating missing parts can be seen as faking or misleading a buyer, so the article stresses full documentation. It also says that professionally carried out restoration, if documented, will not make a significant difference to the value, and that for heavily damaged items the cost of restoration often outweighs the value gained. It does not give a method for detecting restoration, but implies that a colour match without appropriate age and wear looks out of place, which is a clue a buyer can use.
For the house, the rule that follows is that any work on a toy is stated in the description with the date, the extent and the person who did it, if known. A repainted tank, a replaced dome or a new set of rubber tracks is not a fault in itself. It becomes one when it is not said.
Vinyl, Celluloid and the Slow Chemistry
Plastics age differently from metal. The 2020 review of plasticiser loss in heritage collections by King, Grau-Bove and Curran, which the chapter on soft vinyl describes at greater length, found in a survey of about 7,900 plastic objects at the Victoria and Albert Museum that roughly 10 per cent showed chemical damage such as bloom, brittleness, discolouration or sweating. In the European POPART survey, about 23 per cent of PVC objects were sweating or had a sticky surface. These are museum figures and not toy figures, but they show that a vinyl toy cannot be assumed to be stable.
The review's practical points can be stated simply. Low temperature slows the loss. Enclosure can reduce migration, although ventilated containers can increase it. A plasticised object should not be stored in contact with plastics that can absorb its plasticiser, and visual inspection alone is not reliable, since some objects lose plasticiser without visible signs. The authors discuss PVC and cellulose acetate, with some attention to cellulose nitrate. They do not discuss toys, and the guide does not claim that any one toy will behave as the survey objects did.
The Gunpla article adds a note on kits. It says that some kits had an internal frame pre-assembled on the runner but that this approach has mostly been phased out because the softer plastic degrades over time. A sealed box is therefore not a guarantee about the plastic inside it. A description of a sealed kit or an unopened vinyl figure should say when the seal was last checked, and should not claim that the contents are as they were made.
When a Third Party Grades the Toy
Third-party grading is an alternative to a dealer's own word. Wheeljack's Lab, a dealer in graded toys, describes the best-known company, AFA, as a grader that stemmed from the Collectible Grading Authority and began grading in 2000. It says AFA uses a modern scale, a ten-point scale with bronze, silver and gold categories, for toys from 1995 to the present, and a standard scale for older toys, which may have a wider range of possible flaws. Grading is based only on the toy's appearance, regardless of rarity.
The process has three steps: pre-grading, grading and verification, with junior and senior graders, and each graded toy is sealed in a clear acrylic case with a small opening at the back for air circulation. The article says the cases offer some UV resistance against yellowing and fading and protect against water damage, bending and dust. It lists costs, with smaller figures usually under 50 US dollars to grade and premium service often 100 dollars or more, and turnaround times of about three weeks for the priority tier and 75 or more business days for the standard tier. Previously opened, yellowed, bent or damaged toys often do not qualify.
The source has its own interest. Wheeljack's Lab buys and sells graded toy collections, so its account of grading is promotional, and the chapter treats it as a description of what the service claims and not as an independent assessment. The article's own conclusion is that grading is worthwhile mainly for old toys in excellent condition, and that worn or damaged toys may not justify the cost and the delay. For tin toys with their boxes, a sealed acrylic case also makes it hard to inspect the underside, the mechanism or the marks, which the sections above show to be where much of the evidence lies.
Prices, Records and What Changed in 1996
The Collectors Weekly interview with Pinchot gives the market's turning point. Matt Wyse's robot collection was sold at Sotheby's in 1996, and Pinchot says it was the first time a major house had handled toy robots. That decision gave tin lithographed toys a huge amount of credibility, he says, and prices rose quickly afterward. The sale also brought a rare variation of the Gang of Five, the Machine Man, out of the attics, and the interview records a Machine Man sale at 42,000 US dollars, a figure that the interviewer gave and Pinchot confirmed.
He also describes a cooling. As of 2010 several major collections had been sold in the previous two years, and he said the market was quite saturated and prices were down, calling it a great time to buy and expecting prices to rise again within a couple of years. He adds that several more Gang of Five robots had surfaced, lowering their rarity. These are statements about a moment, and the chapter does not claim that they are true now.
At the other end, the Journal of Antiques says most Japanese tin toys were sold in five-and-dime and hardware or grocery stores, including Woolworth, Grants and McCrory's, and typically retailed for about 1.95 to 3.95 US dollars. It gives a current general range of roughly 30 to 300 dollars, with some pieces valued up to 500 with the box, and says toys have held their value better than many other collectibles. The article is dated 2023, its figures are not the house's, and the guide quotes them only to show the range.

A toy shop in Gotokuji, Tokyo; photographed by nagi usano; CC BY 4.0. Photograph by nagi usano, CC BY 4.0. Wikimedia Commons, File:おもちゃのとばり 豪徳寺 Goutokuji (55529229107).jpg.
Look closer: Prices are set shop by shop. The sources read for this chapter do not describe this one.
Image: nagi usano, CC BY 4.0, via Wikimedia Commons
Pinchot's advice to a new buyer is practical. Attend shows to meet knowledgeable dealers, read the reference books and sale catalogues, and talk with experienced collectors before the first purchase. He also names the danger of reproductions, saying that they hurt the market because buyers who would pay about 1,000 dollars for an original may instead buy a close copy for 20 dollars, although he adds that they can also raise interest and encourage preservation.
Fifteen Facts for Any Description
The table below turns the guide into a form. A description that supplies these facts can be compared with any other, whatever scale it uses.
| Fact | What to record | Where the guide found it |
|---|---|---|
| Object and maker | Name, maker's mark, importer, licence holder, as marked | Journal of Antiques; chapter on makers |
| Marks seen | Each mark, its position, and what it is believed to be | Journal of Antiques; Collectors Weekly |
| Date evidence | Materials, mechanism, dated events, the latest reference on the box | Journal of Antiques; Showa chronicle |
| Scale and grade | Name of the scale, the grade and the words behind it | Mandarake; a UK dealer; AFA |
| Box | Present or absent; original to the toy; damage; printed marks | Journal of Antiques |
| Paint | Original, touched up or repainted, and where | Journal of Antiques |
| Materials | Tin, plastic, celluloid, vinyl, rubber; any replaced part | Journal of Antiques |
| Function | Working or not; power source; how tested; number of actions | Journal of Antiques |
| Batteries | Removed or not; any sign of leakage | Journal of Antiques |
| Corrosion | Rust, flaking or weeping; where and how much | Scottish Museums |
| Plastic condition | Tackiness, bloom, brittleness, colour change | King, Grau-Bove and Curran |
| Restoration | What, when, by whom, with documents if any | Littledale |
| Reproduction risk | Marks that fit a later production; brightness of paint; wear | Collectors Weekly; Journal of Antiques |
| Storage history | Damp, attic, shed, cellar, sealed case | Littledale; Scottish Museums |
| Photographs | Front, back, underside, mechanism, marks, box | UK dealer |
How a Careful Description Reads
The following is a pattern, not a piece in stock. It shows the order in which the facts in the table can be set down: the object and the marks seen, with the position of each; the materials and the mechanism, which place it in time; the box, stated as present or absent, original to the toy or not, and its damage; the paint, stated as original or touched up; the function, with the way it was tested; and last, the grade, with the name of the scale and the words that support it.
A reader will notice that the grade comes last. That is deliberate. A grade at the start of a description invites the reader to stop reading, and the evidence that would let him check it is then never seen. A description that puts the facts first can be read by a collector in Tokyo, a museum curator or a buyer who has never handled the object, and each will reach the same understanding. It also protects the writer. A description that says what was checked and what was not can never be accused of claiming more than it knew.
The same pattern serves for vinyl and kits, with changes in the facts: for a vinyl figure the foot marks, the size class and the plastic's condition, and for a kit the grade, the scale, the year, the seal and the completeness of the runners. The chapters on soft vinyl and on Gunpla say which marks and dates the sources give.
A Short Glossary of Condition
The terms below are used as the sources use them.
| Term | Meaning in these sources |
|---|---|
| Mint | Mandarake's grade 10: the best possible condition the item can be in. |
| Near mint | In the UK dealer's scale, 8.0 to 9.0, with minor marks noticeable only on close inspection. |
| Original | Part or finish as the maker made it. |
| Restored | Repaired or replaced; the description should say what. |
| Repainted | Paint added over or in place of the original; lowers value, says the Journal of Antiques. |
| Major action | A toy with three or more movements. |
| Rarity number | A one-to-ten scale for battery-operated toys, 1 very common to 10 very scarce. |
| Patina | The surface that age gives a metal; museum guidance says never remove it. |
| Bloom | A surface film on plastic from migrating plasticiser. |
| Acrylic case | The sealed case in which AFA returns a graded toy. |
Fun Facts About Condition
- Mandarake moved all its categories to one ten-point scale in May 2024.
- A box in good condition can be worth twice the toy, according to the Journal of Antiques.
- Early robot boxes often showed robots stomping through cities, Pinchot says.
- A Machine Man robot, about 18 inches tall, is recorded in the Collectors Weekly interview as selling for 42,000 US dollars.
- Most Japanese tin toys first retailed for about 1.95 to 3.95 US dollars.
- Some tin collectors accept up to about 15 per cent plastic and others none.
What People Ask About Condition and Grades
People ask which grading scale is best. None is best in itself, because they measure different things. Mandarake names ten steps, a UK dealer gives overlapping bands, and AFA sorts modern and older toys into two scales. The best practice is to read the words and photographs that come with a grade and not the number alone.
People ask whether to restore a toy. Littledale advises leaving minor damage alone and sending serious damage to a professional, and he notes that restoration is costly and that its cost often exceeds the value gained. If work is done, it should be documented, since recreating missing parts without saying so can be seen as faking.
People ask how to tell a reproduction. The sources give several tells: Lilliput reproductions carry a Tin Tom Toy logo instead of the original's KT mark and no Made in Japan marking, a Lilliput reproduction can have embossed eyes instead of concave ones, and the Journal of Antiques, writing of reproduced Christmas tin toys, names overly bright paint and tin and a lack of normal wear as warning signs, which is a sound habit of looking for other tin as well. The Myths chapter sets them out together.
Boxes, Reproductions and Marks

A Horikawa Monster Robot box, with an importer's sticker at the foot. Photograph by D J Shin, CC BY-SA 3.0. Wikimedia Commons, File:S.H Horikawa Monster Robot Box Art.jpg.
Look closer: The sticker names the company that sold the toy. The maker's mark is a separate thing and sits elsewhere on the box or the toy.
Image: D J Shin, CC BY-SA 3.0, via Wikimedia Commons

The Commons title gives the maker as unknown and the toy as a mini reproduction. Photograph by D J Shin, CC BY-SA 3.0. Wikimedia Commons, File:Unknown Japanese Maker – Mini Repro Mr. Atomic – Box Art.jpg.
Look closer: Not every box can be given a maker. The Commons title records this one as an unknown Japanese maker, and the sensible description does the same.
Image: D J Shin, CC BY-SA 3.0, via Wikimedia Commons

A reproduction of a Yonezawa robot sold under the American importer's name Cragstan, from the Osaka Tin Toy Institute's Tin Age Collection. Photograph by D J Shin, CC BY-SA 3.0. Wikimedia Commons, File:Osaka Tin Toy Institute The Tin Age Collection Cragstan Yonezawa Reproduction Mr. Atomic Side.jpg.
Look closer: A reproduction is honest when it is labelled. The danger comes when the label is lost or the marks are removed.
Image: D J Shin, CC BY-SA 3.0, via Wikimedia Commons
Condition at the Desk
The house's own guide to the care of tin toys sets out how to look after them. The shelf includes Showa tin pieces such as a boxed Alps Planet Explorer tin space tank. Stock changes; the shelf page shows what is here now.
Answered plainly
What is Mandarake's top grade?
Ten, Mint, defined as the best possible condition the item can be in, on a scale that has applied to all categories since May 2024.
Does a box add value?
The Journal of Antiques says a box in good condition can be worth twice the price of the toy in some cases.
Should I repaint a worn toy?
No. The Journal of Antiques says repainting lowers value, and the museum restorer Chris Littledale advises leaving minor damage as it is.
What humidity is safe for metal?
The Scottish Museums factsheet gives below 65 per cent relative humidity as dry.
Does PVC deteriorate?
Yes: about 23 per cent of PVC objects in one European survey were sweating or sticky.
Where next
Sources and image credits
- Item conditions, Mandarake
- Grading vintage toys, a UK dealer (vintagetoysgames.co.uk)
- Should you grade your toys? Pros and cons of AFA grading, Wheeljack's Lab
- Japanese Tin Toys: A Craze That Rebuilt Post-War Japan, Journal of Antiques, 20 September 2023
- Attack of the Vintage Toy Robots, interview with Justin Pinchot, Collectors Weekly, 18 November 2010
- Vintage Toy Robots: How To Spot The Real Lilliputs From the Repros, Collectors Weekly, 18 November 2010
- Restoring Tinplate, Chris Littledale, Brighton Toy and Model Museum
- Care guidance for metal objects, factsheet, Scottish Museums
- Plasticiser loss in heritage collections: its prevalence, cause, effect, and methods for analysis, Heritage Science 8, 2020
- Gunpla, Wikipedia
- Object record, File:Mandarake (4970180671).jpg, Wikimedia Commons
- Object record, File:Masudaya Battery Powered Army Tank M-99 Tin Toy Box Art.jpg, Wikimedia Commons
- Object record, File:Billiken Shokai Tin Wind Up Robby the Robot with Disintegrator Ray Gun Olive Green Version Box Art.jpg, Wikimedia Commons
- Object record, File:Rocket USA – Masudaya – Tin Wind Up – Mini Shooting Giant Robot (ミニ シューティング ジャイアント ロボット) – Gang of Six!! – Back Side.jpg, Wikimedia Commons
- Object record, File:Masudaya Battery Powered Army Tank M-99 Tin Toy Front.jpg, Wikimedia Commons
- Object record, File:Tintoy museum.JPG, Wikimedia Commons
- Object record, File:おもちゃのとばり 豪徳寺 Goutokuji (55529229107).jpg, Wikimedia Commons
- Object record, File:S.H Horikawa Monster Robot Box Art.jpg, Wikimedia Commons
- Object record, File:Unknown Japanese Maker – Mini Repro Mr. Atomic – Box Art.jpg, Wikimedia Commons
- Object record, File:Osaka Tin Toy Institute The Tin Age Collection Cragstan Yonezawa Reproduction Mr. Atomic Side.jpg, Wikimedia Commons
Last reviewed 28 October 2026. Pictures, where shown, are public-domain or open-access and credited beneath each one.
Looking for a particular tin toy, doll or figure, or a view on one you own? The concierge desk replies within one to three business days.
Browse Retro, Vintage, Antique and Modern Toys · Make a private request
Private concierge
Looking for something in particular?
Describe the piece or the project you have in mind. A senior advisor in Tokyo reads every case file personally and replies within two business days, with fees set out in writing before any work begins.