Rolex Sea-Dweller, Deepsea and Yacht-Master: Down and Across
The Sea-Dweller is the Rolex built for the trip home, and the Yacht-Master is the Submariner taught to sail. Both grew from the 1953 diver, and they parted ways at the waterline. One line went down into saturation diving, the helium valve and finally the floor of the Mariana Trench. The other went across the surface, into regattas, platinum and gold. The hardest problem in deep diving turned out to be the ascent, and Rolex answered it with a small piston in the side of the case. Japan answered the same problem in 1975 with a sealed titanium case and no valve at all.
| Sea-Dweller | Deepsea | Yacht-Master | |
|---|---|---|---|
| First made | 1967, for saturation diving | 2008, with the Ringlock case | 1992, for sailors |
| Built for | The decompression after long dives | Pressure beyond human diving range | Timing on the water |
| Rated depth | 610 m, then 1,220 m from 1978 | 3,900 m; 11,000 m for the Challenge | 100 m |
| Signature part | Helium escape valve, patented 1967 | Ringlock compression ring | Bezel turning both ways, raised numerals |
| Classic reference | 1665, then the 16600 | 116660 | 16622 in steel and platinum |
| Japan's chapter | A 1968 letter from a diver in Hiroshima | The blue dial, about three in ten seen | The 16622, about one in seven seen |
A telegram from the trench, 1960
Happy to announce that your watch works as well at 11,000 metres as it does on the surface.
Jacques Piccard, oceanographer, telegram to Rolex, 1960
On 23 January 1960 the bathyscaphe Trieste reached the bottom of the Challenger Deep in the Mariana Trench. Jacques Piccard and US Navy Lieutenant Don Walsh were aboard, and an experimental watch was strapped to the hull. It was the Deep Sea Special, and it came back up in working order. The descent took almost five hours, and the two men stayed on the bottom for twenty minutes. Our Rolex house history tells how the sealed Oyster case of 1926 came to be. The Sea-Dweller and the Yacht-Master took that seal to its limits.
The 1960 watch was the third Deep Sea Special. Rolex had tested two earlier versions through the 1950s, and the third was built for the Challenger Deep. The house had been supplying the Piccard family since 1953, when Auguste Piccard dived in the first Trieste. That same year Oysters went to the summit of Everest with the Hunt expedition. Accounts differ on the depth of the 1960 dive: 10,916 metres in the house figures, 10,912 metres in the later expedition record. We print both, because the instruments of 1960 were cruder than those of 2012.
The Deep Sea Special was never sold. It measured 42.7 mm across and 36 mm high, under a Plexiglas crystal 18 mm thick. It was made to ride on a hull, and no diver could have worn it. Its job was to prove that an Oyster case could survive full ocean depth. The lesson ran forward for half a century, into the Deepsea of 2008 and the Deepsea Challenge of 2022. Japan's own first diver's watch was still five years away, in 1965.
See also: the Watch Almanac, for the family tree of every house in our Journal, and Ginza and the watch, for the Tokyo street where Seiko began.
Helium, the gas that gets in
Saturation diving changed what a diver's watch had to survive. In the 1960s divers began to live for days or weeks in pressurised habitats on breathing gas rich in helium. They stayed at the pressure of their worksite, and they decompressed only once, at the very end of the mission. Before a dive, the divers spent days in a chamber filled with a helium and oxygen mix. The method let a team work at depth for days at a time.
Helium atoms are very small, and they slip through gaskets that keep out water. Over days in a chamber, a watch case slowly fills with helium, just as the diver's body does. On the way back up, the body sheds the gas faster than the watch can. Pressure builds inside the case, and the weakest part gives way. On the divers' watches of the 1960s that part was the acrylic crystal, which could pop clean out. The watch kept running in the chamber and failed in the hour of decompression.
The Rolex answer is a one-way valve set into the side of the case at nine o'clock. Inside a sealed cylinder sits a piston held by a spring. When the pressure inside rises too far above the pressure outside, the piston slides out and lets the gas go. It closes again on its own, so water cannot get in. The house sums up the principle in one line: the true feat lies in the journey back to the surface. Our reading: that sentence describes the whole Sea-Dweller line.
See also: the Fifty Fathoms, for the other great diver's watch of 1953, and Oris and its divers, for another house's answer to the same water.
Sealab, Comex and the first valves
The trouble showed up first in American navy habitats. Divers in the Sealab programme noticed that their Submariners lost crystals in the decompression chamber after a dive. Sealab was built to study long stays under water, and in 1965 the former astronaut Scott Carpenter spent thirty days below. By then the Submariner was rated to 200 metres, so depth alone was never the issue. The gas was.
Rolex filed its patent for a self-acting gas escape valve on 6 November 1967. The Swiss patent, CH492246, was granted in June 1970, more than two and a half years later. In between, the first watches carried casebacks engraved Patent Pending. The earliest Sea-Dwellers had a single line of red text on the dial, and collectors call them the Single Red. They were rated to 500 metres, and the first of them had no valve at all.
The first Sea-Dweller with a valve prototype went to Dr Ralph W. Brauer, an American hyperbaric researcher. His watch was tested in the Hydra 1 experiment, run with the French diving firm Comex in 1968. Rolex then fitted valves to some of the 1967 Single Reds and handed them to the Sealab III aquanauts in October 1968. That programme was abandoned after a fatal accident, and the long helium test it promised never happened. Rolex also refitted standard 5513 Submariners with the valve, and these became the reference 5514.
A correction to the common story: the first Sea-Dwellers were not made for Comex. From 1968 to 1971 Comex worked only with Omega, testing a 600-metre prototype that became the Seamaster 600. Its divers still wore Omega prototypes in the Sagittaire 1 trial, which ended on 2 December 1971. The Rolex agreement came at the end of that year, and the house dates its Comex partnership to 1971. Our Omega house history follows the other side of that rivalry.
The first ten Rolex watches went to Marseille in late 1971. They were Double Red Sea-Dwellers with case numbers in the 2.6 million range and the first Rolex Patent casebacks. Each was signed Rolex-Comex on the back and numbered from 1 to 10. In February 1972 two Comex divers spent 100 hours at a simulated 500 metres in the Sagittaire 2 trial. On 24 May 1972, in Physalie 6, Robert Gauret and Patrice Chemin went to 610 metres, the watch's full rating. The Sea-Dweller has been standard issue for Comex divers since 1977.
See also: Tudor's Submariner, for the sister house's divers of the same years, and Rolex serial numbers, for reading a case number like 2.6 million.
The Double Red and the Great White
The reference 1665 was the first production Sea-Dweller. Its 40 mm steel case carried the valve on the left flank and a date at three o'clock. Divers needed the date to count long stays in a chamber. There was no Cyclops lens, because a glued lens would not have survived the test pressure. The crystal was thick, domed acrylic, about 2.5 mm thicker than the Submariner date's. Inside ran calibre 1575, with a date and no quickset.
The depth rating rose from 500 to 610 metres in 1969, and a second red line appeared on the dial. The two red lines read Sea-Dweller and Submariner 2000, the depth in feet. Rolex sold the Sea-Dweller to the public from late 1970, after the patent came through. Regular production of the Double Red ran from 1971 to 1977. Collectors sort its dials into Marks, from Mark 0 to Mark 4, with later service dials beyond. In Japan the Double Red has its own short name, aka-shīdo, red Sea.
From 1977 the red print turned white, and Submariner 2000 was dropped from the dial. Collectors call this version the Great White. It kept the same reference, case and depth rating as the Double Red. It was the last Sea-Dweller under an acrylic crystal. Production of the 1665 ended in 1983. Accounts differ on the end date, and some date the last 1665 to about 1980.
Some 1665s were made for Comex and carry its name on the dial. These are the rarest everyday Sea-Dwellers, and fewer are thought to exist than Comex Submariners. Their delivery series is documented, so a case number can be checked. We found no record of an official production total for the 1665; we do not speculate. Of the Sea-Dwellers we saw in Japan in October 2026, the 1665 and 16660 together were about one in six.
See also: Japanese condition ranks, for how Japan grades an old dial, and box and papers, for what a full set adds to a vintage watch.
A letter from Kure, 1968
Japan met the helium problem through the post. In 1968 a letter of complaint reached K. Hattori and Co., the Tokyo house behind Seiko. It came from Yo Oshima, a diver at Nihon Kaiyō Sangyō, later Sumitomo Marine Development. He worked from a diving bell at 350 metres, and he said Seiko's 300-metre diver was unfit for his job. The letter set off seven years of work. Our Seiko house history tells how Hattori built the company.
I am a diver who works at depths of 350m using a diving bell.
Yo Oshima, saturation diver, letter to K. Hattori and Co., 1968
Seiko sent two men to see him: Taro Tanaka, its development leader, and Akabane, a design engineer from the Suwa factory. They visited a drillship at Kure Port in Hiroshima and saw the bell, the helium and oxygen gas and the decompression chambers. Tanaka was the development leader and designer of the watch that followed. Other accounts credit a team led by the senior engineer Ikuo Tokunaga. We print both names, as the two roles may simply differ.
Seiko answered the problem from the other side. Rolex let the helium out through a valve, and Seiko set out to keep it out. The Professional Diver's 600m of June 1975 had a one-piece titanium case, the first on any diver's watch. An L-shaped gasket kept the helium out with no need for an escape valve. An outer shroud guarded the case, and four screws let it come off for cleaning. Its unusual build later earned it the nickname Tuna among collectors worldwide.
The watch led to twenty new patent, utility model and design registrations. They covered the case, the dial and hands, and a polyurethane strap with folds like an accordion. The old PVC strap went brittle in cold water and loosened under pressure, and the new one did neither. In a 1982 test under 300-metre saturation, the maker's figures showed its glass up to ten times more resistant to helium than others. In May 1983 two of these watches rode outside the submersible Shinkai 2000 and survived 1,062 metres. A ceramic-shrouded 1000-metre model replaced it in 1986, with quartz inside since 1978.
See also: Japanese independent horology, for the small Japanese makers who followed, and Grand Seiko and Credor, for the Suwa works at its most refined.
Records under pressure
The Sea-Dweller made its name in habitats and chambers. In 1969 Rolex joined Tektite, an underwater habitat programme run by NASA, the US Navy and the US government. Four aquanauts lived on the floor of the Caribbean for 58 days wearing Rolex watches. In the Tektite II mission of 1970, the marine biologist Sylvia Earle led an all-women team. In 1970 Rolex also brought in the Triplock crown, with three sealed zones, first fitted to the Sea-Dweller.
Comex, founded in Marseille in 1961, built the chambers where the records were set. In 1978 the rating doubled to 1,220 metres, and the new depth was proved in chambers developed with Comex. In the Hydra VIII expedition of 1988, six divers wearing Sea-Dwellers worked at 534 metres in the open Mediterranean. They left their pressurised habitat and connected a pipeline, an open-sea record. In the Hydra X programme of 1992, Théo Mavrostomos reached 701 metres in a simulated dive. His mission lasted 43 days, and he wore a Sea-Dweller throughout.
Mavrostomos worked with Comex for twenty years. France gave him its Order of Merit in 1997 for the 701-metre dive, and Rolex used him in its advertising. A 16600 issued to him in 1998, with an engraved back and all its papers, has since come to light. The record still stands. Our reading: the Sea-Dweller's fame rests on a small number of working divers, and that is the point.
Sapphire and 1,220 metres
The reference 16660 of 1978 was the first modern Sea-Dweller. It was among the first Rolex watches with a sapphire crystal, and it doubled the rating to 1,220 metres. The bezel now turned one way only, and the valve grew larger. Calibre 3035 replaced the 1575, with a faster beat and a quickset date. Collectors call it the Triple Six. In 1984 its matte dial gave way to a gloss one with white gold surrounds around the markers.
The reference 16600 followed in 1989 and ran for twenty years, the longest of any Sea-Dweller. It kept the sapphire and the 1,220-metre rating and took calibre 3135, with a longer reserve and a full balance bridge. Its lume changed twice, and the foot of the dial tells which. T Swiss T<25 means tritium, Swiss alone means Luminova, and Swiss Made means Super-LumiNova. It was the last Sea-Dweller with an aluminium bezel insert. In its final year, 2008, Rolex made a run for the Italian police divers with an octopus on the dial.

The 16600 is the Sea-Dweller most often seen in Japan today. Of the Sea-Dwellers we saw there in October 2026, about one in four was a 16600. Our own Sea-Dweller 16600 is a 40 mm steel example with a black dial, worn and honest. An old rating tells you nothing about a used watch, so test it before it goes near water. Seven of the Sea-Dwellers we saw were described by their tritium dials. The wider collectible watches shelf holds its peers from other houses.
See also: kept in the box, for why so many Japanese watches survive in good order, our grading guide, for how each piece here is graded, and Luminox, for the story of tritium light on a dial.
The Deepsea and the Ringlock case
In 2008 the 16600 gave way to two watches. One was the Deepsea, reference 116660, rated to 3,900 metres in a 44 mm case. That is well beyond the range of any human diver. Its Ringlock case was the first on a Rolex. A ring of nitrogen-alloyed steel sits inside the middle case, and the crystal and back rest against it. The crystal is domed sapphire 5.5 mm thick, and the back is RLX titanium. The case still stays under 18 mm thick.
Every Deepsea is tested with a 25 per cent margin, to the pressure at 4,875 metres. Rolex built the test tank with Comex. At that pressure the crystal bears almost 4 tonnes, the ring 4.5 tonnes and the caseback 5 tonnes. The same year brought the Glidelock clasp, which lets the bracelet grow by up to 20 mm without tools. In steps of about 2 mm it fits over a diving suit up to 3 mm thick. A Fliplock link adds a further 27 mm for a thick suit.
In 2014 the Deepsea gained the D-blue dial, a gradient from deep blue to black. It recalls the ocean's twilight zone, where the last light from the surface fades. The word DEEPSEA is printed in green, after the colour of Cameron's submersible. The reference 126660 of 2018 brought calibre 3235, wider lugs and a broader bracelet. The 136660 followed in 2022, and in 2024 Rolex made the Deepsea in 18 ct yellow gold for the first time. That gold watch has a blue bezel, a blue dial and a compression ring in ceramic.
Japan took to the blue dial. Of the Deepseas we saw in Japan in October 2026, about three in ten were described as D-blue. The current 136660 made up about one in three. Our reading: Japan's collectors treat the Deepsea as a modern watch to wear, and the 1665 as the one to study.
See also: Zodiac and the Sea Wolf, for a Swiss diver's watch of the 1950s, and vintage Citizen, for Citizen's Parawater and its divers.
Cameron's solo dive
On 26 March 2012 James Cameron dived alone to the bottom of the Challenger Deep. He reached 10,908 metres, the first person to reach full ocean depth in a craft with one pilot. The first reading was 10,898 metres, later corrected by the expedition team. He spent about three hours on the bottom. The trip was part of a joint expedition with National Geographic and Rolex. His craft made thirteen test and research dives between 31 January and 3 April 2012.
She kept me company on the dive to the most remote place on this planet, and was my good luck charm.
James Cameron, film-maker and explorer, 2012
Two watches made the dive. Inside the cockpit Cameron carried the Old Lady, a sister of the 1960 Deep Sea Special. Outside, on the manipulator arm, rode an experimental Deepsea Challenge. Rolex had four weeks to build it, against the six months the task would ideally need. It was guaranteed to 12,000 metres and tested to 15,000 metres. At that test depth the crystal bore 17 tonnes. The sapphire was 14.3 mm thick, and the back was grade 5 titanium.
At the end of 2022 Rolex put the idea into regular production. The Deepsea Challenge, reference 126067, is 50 mm across and made of RLX titanium. It is rated to 11,000 metres. Its crystal is 9.5 mm thick, and its cold-worked ring is about 10 per cent smaller in volume. It is tested to 13,750 metres in a tank built with Comex, with almost 15 tonnes on the crystal. The back is engraved Mariana Trench with the dates of both dives, 23-01-1960 and 26-03-2012.
The Sea-Dweller at 43 mm
The plain Sea-Dweller came back in 2014 as the reference 116600, often called the Sea-Dweller 4000. It kept the 40 mm case and took a ceramic bezel, a Maxi dial and the Glidelock clasp. It lasted until 2017, the shortest run of any Sea-Dweller. For the fiftieth anniversary in 2017 Rolex made the reference 126600. The case grew to 43 mm, and calibre 3235 brought about 70 hours of reserve. It was the first Rolex Professional watch with that calibre.
The 126600 broke one old rule. It was the first Sea-Dweller with a Cyclops lens over the date. It also brought back a single line of red text, a nod to the first watches of 1967. A version in Rolesor, steel with yellow gold, followed. Its year is disputed. Of the Sea-Dwellers we saw in Japan in October 2026, the 126600 and the 1665 were seen about equally often.
See also: our authenticity guarantee, which covers every watch we offer, and duties and customs, for what to expect when a watch crosses a border.
Rolex at sea before 1992
The other branch began on the surface. In 1958 Rolex formed an alliance with the New York Yacht Club, the founder of the America's Cup. Ties with other yacht clubs and their regattas followed around the world. In 1967 Sir Francis Chichester finished a solo voyage round the world from west to east, the first by any yachtsman. He covered about 25,700 nautical miles in 226 days, with a single stop in Sydney. He wore an Oyster Perpetual.
During my voyage around the world in Gipsy Moth IV, my Rolex watch was knocked off my wrist several times without being damaged. I cannot imagine a hardier timepiece.
Sir Francis Chichester, yachtsman, 1968
In 1985 Rolex took its name to the Maxi Yacht Rolex Cup at Porto Cervo in Sardinia. It is a yearly event for yachts longer than 60 feet, racing over 15 to 35 nautical miles. None of this needed a special watch. An Oyster was waterproof, and a sailor could read a plain dial. What sailors lacked was a bezel made for counting minutes between marks and a watch that looked at home ashore. The Yacht-Master supplied both.
A Submariner dressed for the deck
The Yacht-Master arrived in 1992, designed specifically for sailors. The first reference was the 16628, a 40 mm watch in 18 ct yellow gold. It looked like a Submariner, but its case was thinner and its bezel turned both ways. That bezel times intervals such as the sailing time between two buoys. Its numerals stand in relief and are polished against a matt ground. It is rated to 100 metres, like an Explorer or a Datejust.
The Yacht-Master was a luxury watch from the start, made at first in gold alone. In 1994 Rolex added a 35 mm mid-size and a 29 mm ladies' model. It was the first time a Rolex Professional watch came in sizes below the standard one. It was also the only sports model that could be bought as a matching pair. Steel and yellow gold, which Rolex calls Rolesor, came next. Accounts differ on the year, and we print both 1996 and 1997.
In 1999 Rolex introduced Rolesium on the Yacht-Master, a steel case and bracelet with platinum elements. The reference 16622 put a 950 platinum bezel and a platinum dial on a 40 mm steel watch. It ran calibre 3135 at 28,800 beats an hour, with about 48 hours of reserve. It stayed in production until 2012. The 116622 replaced it, almost identical to look at, with new lume, a new clasp and a choice of dials. Our Yacht-Master 16622 of 1999 carries an A serial and was serviced by Nihon Rolex in October 2024.

The smaller watches matter in Japan. Of the Yacht-Masters we saw there in October 2026, nearly one in five was a 29 mm or 35 mm model. The 16622 alone made up about one in seven. Our 29 mm Yacht-Master 169622 of 2001 is the smallest Rolesium, with a platinum bezel and dial. Our Lady Yacht-Master 169623 of 2009 pairs steel with yellow gold. Japan has its own marks for platinum and gold, and our hallmark guide explains how to read them.

The line kept changing material. In 2015 an Everose gold Yacht-Master became the first Rolex on the Oysterflex bracelet, which joins the strength of metal to the comfort of elastomer. In 2019 came the Yacht-Master 42, the first at that size. In 2023 Rolex made the 42 in RLX titanium, tested before launch by the sailor Sir Ben Ainslie. Today the watch comes in 37, 40 and 42 mm, in steel with platinum, gold or RLX titanium. The 37 mm model runs calibre 2236 with a silicon hairspring, and the larger ones run calibre 3235.
Regatta clocks
A sailing race begins with a countdown, and a boat must cross the line the moment it ends. In 2007 Rolex unveiled the Yacht-Master II, a chronograph built for that start. It was the first watch with a programmable countdown from one to ten minutes, held in a mechanical memory. The countdown was set through the Ring Command bezel, which links the bezel to the movement. The first models, the 116688 in yellow gold and the 116689 in white gold, were made available in March 2010. The 116681 in steel and Everose followed in 2011.
The steel 116680, with a blue ceramic bezel, came in 2013. The case measured 44 mm. The line was discontinued in April 2024. In 2026 Rolex brought it back in a new generation. The new models are the 126680 in steel and the 126688 in yellow gold, 44 mm across and 13.9 mm thick. Calibre 4162 inside has a column wheel, a vertical clutch and about 72 hours of reserve. The Ring Command bezel is gone, and pushers now set the countdown.
Of the Yacht-Masters we saw in Japan in October 2026, about one in ten was a Yacht-Master II. We saw four of the new 126680 already. Our reading: the Yacht-Master II is the only watch in this family that does a job no other Rolex does.
See also: Corum and the Admiral's Cup, for another house that tied its name to sailing.
Know the watch at a glance
Most of these watches can be told apart in seconds by four things. Look for the valve, the crystal, the bezel and the line of red. The table gives the shortest test for each key reference.
| Reference | Years | Size | Tell-tale |
|---|---|---|---|
| 1665 Double Red | 1971–1977 | 40 mm | Two red lines, domed acrylic, no Cyclops |
| 1665 Great White | 1977–1983 | 40 mm | White text, no Submariner 2000 line |
| 16660 Triple Six | 1978–1989 | 40 mm | Sapphire, 1,220 m, matte then gloss dial |
| 16600 | 1989–2008 | 40 mm | Aluminium insert, Swiss line shows the lume |
| 116660 Deepsea | 2008– | 44 mm | Ringlock ring visible at the flank, 3,900 m |
| 126600 | 2017– | 43 mm | Cyclops, one red line |
| 126067 Deepsea Challenge | 2022– | 50 mm | RLX titanium, 11,000 m |
| 16622 Yacht-Master | 1999–2012 | 40 mm | Platinum bezel and dial on steel |
| 116680 Yacht-Master II | 2013–2024 | 44 mm | Ring Command bezel, regatta countdown |
The valve sits at nine o'clock on every Sea-Dweller and Deepsea, and on no Yacht-Master. A Yacht-Master bezel turns both ways, while a Sea-Dweller bezel turns one way only from the 16660 on. Before anything else, check the case and back against the papers.
Where the record differs
| Question | What the accounts say | Our reading |
|---|---|---|
| Depth of the 1960 dive | 10,916 m in the house figures, 10,912 m in the expedition record, 10,911 m in one timeline | About 10,900 m; the gauges of 1960 were cruder |
| Piccard's telegram | One house page prints a smooth sentence; a 2012 text prints a terser version | We quote the house page and note the other |
| First valve on a wrist | Patent filed in 1967 and retrofits that year; a Japanese history says first fitted in 1968 | Designed in 1967, worn in tests from 1968 |
| End of the 1665 | 1983 in one timeline; about 1980 in Japanese guides | Overlap with the 16660 is certain; the last year is not |
| Run of the 16660 and 16600 | 16660 to 1988 or 1989; 16600 to 2008 or 2009 | 1978 to 1989, then 1989 to 2008 |
| Deepsea crystal | 5.5 mm in the maker's figures, 5 mm in one history | 5.5 mm |
| Rolesor Sea-Dweller 126603 | 2019 in two histories, 2023 in one timeline | 2019 |
| Two-tone Yacht-Master | 1996 in one account, 1997 in a Japanese history | We print both |
| First Rolesium | 1999 in the house history, 1997 in one encyclopaedia | 1999 |
| Yacht-Master II | Unveiled 2007, available from March 2010 | 2007 for the idea, 2010 for the watch |
| Seiko's 600m team | Taro Tanaka as development leader; a team led by Ikuo Tokunaga | Both men, in different roles |
Most of these gaps are a year wide, and most come from the gap between a launch and the first watches in a customer's hands. Some date the first exploding crystal to a Comex report of 1964. We found no record of that 1964 report elsewhere; we do not speculate.
What we checked and left out
What we checked and left out. One count puts the earliest 1665s at slightly over 100, with no official figure behind it, so we give no number. A blue-dial 16622 made for Hong Kong around 2012 is said to number 50; we could not confirm the count, so we leave it out. The pressure at which the valve opens appears in one technical page we could not open, so we print no figure. Seiko's ten-times figure for helium resistance is the maker's own test, and we give it as such. We quote no prices from today's trade.
Our earlier guides, revisited
Our Submariner guide ends where this one begins, with the 5513 and the first valve. We now add the 5514 and the Comex years to that story. Our guide to Rolex reference numbers explains why the 16600 has five digits and the 126600 six. Our vintage Seiko divers guide covers the 600m Tuna as a watch. The letter from Kure started it. The record here agrees with both.
A timeline
| Year | Event |
|---|---|
| 1953 | Rolex supplies Auguste Piccard and the first Trieste |
| 1958 | Alliance with the New York Yacht Club |
| 1960 | The Deep Sea Special reaches the Challenger Deep |
| 1965 | Japan's first diver's watch |
| 1967 | Sea-Dweller and valve patent; Chichester sails home |
| 1968 | Brauer's prototype; the letter from Kure |
| 1969 to 1970 | Double Red, 610 m; Tektite; patent granted; Triplock |
| 1971 | Comex partnership; ten Rolex-Comex watches |
| 1975 | Seiko's Professional Diver's 600m |
| 1977 | The Great White |
| 1978 | The 16660, sapphire and 1,220 m |
| 1988 | Hydra VIII at 534 m |
| 1989 | The 16600 |
| 1992 | Hydra X at 701 m; the Yacht-Master |
| 1999 | Rolesium and the 16622 |
| 2007 | The Yacht-Master II is unveiled |
| 2008 | The Deepsea and Ringlock; Glidelock |
| 2012 | Cameron's solo dive |
| 2014 | D-blue dial; the 116600 |
| 2017 | The 43 mm 126600 |
| 2022 | The Deepsea Challenge 126067 |
| 2023 | Yacht-Master 42 in RLX titanium |
| 2024 | Gold Deepsea; Yacht-Master II withdrawn |
| 2026 | A new Yacht-Master II |
Why the return matters most
Every diver's watch is sold on depth, and the number on the dial is the first thing anyone reads. The Sea-Dweller's real advance had nothing to do with depth. The Submariner could already reach 200 metres when the Sea-Dweller arrived. What failed was the trip home, hours after the work was done. Rolex solved it with a valve, and Seiko solved it with a seal. Both answers came from listening to divers: an American researcher in one case, a diver in Hiroshima in the other.
The Yacht-Master took the same case the other way. It kept the shape of a tool and turned it into a watch for a deck, a dinner and a smaller wrist. Its one true tool, the regatta countdown, came fifteen years later in the Yacht-Master II. In Japan, where the 29 mm and 35 mm models are still seen so often, that smaller wrist is plain to see. The two families share a crown and a case, and they answer opposite questions: how to come back from the deep, and how to look right at the surface. That is our reading.
If you are looking for one particular reference, our Otoriyose private request will look for it in Japan on your behalf. If you want to see what is here now, the Rolex room is open.
Answered plainly
What does the helium escape valve do?
It lets helium that has crept into the case escape during decompression, so the crystal stays in place. It matters only after long stays in a pressurised chamber.
How is a Sea-Dweller different from a Submariner?
It has the valve, a higher depth rating and, until 2017, no Cyclops lens. Today it is rated to 1,220 metres and measures 43 mm.
Is the Deepsea a Sea-Dweller?
Yes. It began in 2008 as the Sea-Dweller Deepsea, with the Ringlock case and a 3,900-metre rating.
What is Rolesium?
It is the Rolex name for steel with platinum, introduced on the Yacht-Master in 1999. On the 16622 the bezel and dial are platinum.
Can I swim with an old Sea-Dweller?
Only after a pressure test, because an old rating says nothing about a worn gasket. Gaskets age even when a watch sits in a drawer.
Seen elsewhere
- Even deeperRolex · the Sea-Dweller from Tektite to Hydra X
- The Black Face of the Deep SeaSeiko Museum Ginza · Taro Tanaka's own account
- Then and nowDEEPSEA CHALLENGE · the Trieste beside Cameron's craft
- Conquering the open seasRolex · sailing from 1958 to the new Yacht-Master II
Further reading
- Up: The Rolex house history, for the sealed Oyster case that both families are built on.
- Up: The Seiko house history, for the company that answered the Kure letter.
- Across: The Submariner guide, because both lines begin with the 1953 diver.
- Across: Vintage Seiko divers, for the Tuna and the watches around it.
- Down: The Rolex room, for the Sea-Dweller and Yacht-Masters graded in Tokyo now.
References
- Sea-Dweller: managing decompression (Rolex)
- Sea-Dweller: innovations in service of underwater exploration (Rolex)
- Sea-Dweller: even deeper (Rolex)
- Sea-Dweller (Japanese) (Rolex)
- Anatomy of a Rolex: the helium escape valve (Rolex)
- The Rolex Sea-Dweller models (Rolex newsroom)
- The Rolex Deepsea models (Rolex newsroom)
- The Rolex Deepsea Challenge (Rolex newsroom)
- The Rolex Yacht-Master models (Rolex newsroom)
- Deepsea: journey to the deep (Rolex)
- Rolex Deepsea: overcoming pressure (Rolex)
- Rolex history, 1953 to 1967 (Rolex)
- Rolex Deepsea Challenge press kit, 2012 (Rolex)
- Yacht-Master: a valuable tool watch (Rolex)
- Yacht-Master: conquering the open seas (Rolex)
- Yacht-Master: conquering the open seas (Japanese) (Rolex)
- Then and now: the Trieste and the DEEPSEA CHALLENGER (DEEPSEA CHALLENGE)
- Expedition update: phase II begins, 2012 (DEEPSEA CHALLENGE)
- Reference points: the Rolex Sea-Dweller, 2017 (Hodinkee)
- The Sea-Dweller Chronicles, part two, Jose Pereztroika, 2020 (Rolex Magazine)
- The history of the Rolex Sea-Dweller (Revolution)
- How the Rolex Sea-Dweller became a life saver (Sotheby's)
- The Rolex Sea-Dweller: just the facts (The Watch Club)
- Professional Diver's 600m: the black face of the deep sea, Taro Tanaka (Seiko Museum Ginza)
- Professional Diver's 600m, 1975 (Seiko Museum Ginza)
- History of the Seiko diver's watch (Seiko Watch Corporation)
- The 1968 diver's watch and its heirs, 2020 (Seiko Watch Corporation)
- Seiko dive watch history (Dive Magazine)
- Rolex Yacht-Master (Wikipedia)
- Rolex Yacht-Master II (Wikipedia)
- Rolex Sea-Dweller (Wikipedia)
- The Sea-Dweller 1665 and the Comex years (Japanese) (Evance)
- The Yacht-Master Rolesium 16622 (Japanese) (Evance)
- The red Sea-Dweller and the line through the decades (Japanese) (GINZA RASIN)
- Yacht-Master 16622 and 116622 compared (Japanese) (GINZA RASIN)
- Comex and the Sea-Dweller (Japanese) (Kaitori Rich Tokyo)
- Reference: Sea-Dweller (BezelBase)